2423: Gear, 23-T pinion (48-pitch) (fits 3mm shaft)/ set screw

2526: Screws, 2.5x12 countersunk machine (hex drive) (6)

2554: Screws, 3x6mm caphead machine (hex drive) (6)

2576: Screws, 3x8mm button-head machine (hex drive) (6)

2743: Set (grub) screws, 3mm hardened (12)

2745: Nuts, 3mm nylon locking (12)

3159: Screws, 3x10mm caphead machine (hex drive) (6)/ lockwashers (6)/ hex wrench

3215: Screws, 2.5x6mm cap-head machine (hex drive) (6)

3785: Motor, Titan® 12T (12-Turn, 550 size)

4725: Gear, pinion (25-tooth) (48-pitch) / set screw

7019: Ball bearings, blue rubber sealed (4x8x3mm) (2)

7028: Hollow balls (20)

7028X: Hollow balls, steel (machined) (22)

7045R: Spur gear, 45-tooth

7046R: Spur gear, 50-tooth

7047R: Spur gear, 55-tooth

7054: Stub axle, steel (2)/ yokes (2) (assembled)

7056: Half shafts, center front (1), center rear (1) (internal splined half shafts (2)/external splined half shaft) (2))/ metal u-joints (4)

7057: Yokes, differential and transmission (2)/ 3x10mm screw pin (2)

7061: Shocks, GTR composite, 1/16 E-Revo/Slash (assembled, without springs) (2)

7061X: Shocks, GTR hard anodized, PTFE-coated bodies with TiN shafts (fully assembled, without springs) (4)

7062: Rebuild kit, GTR composite shocks (x-rings, bladders, pistons, e-clips, shock rod ends, hollow balls) (renews 2 shocks)

7063: Shaft, GTR shock (2)

7063T: Shaft, GTR shock (TiN-coated) (4)

7065: Caps and spring retainers, GTR shock (upper cap (2)/ hollow balls (4)/ bottom cap (2)/ upper retainer (2)/ lower retainer (2)

7067: Piston, damper (2x0.5mm hole, red) (4)/ travel limiters (4)

7091: Gearbox halves, front & rear

7092: Input shaft/ output shaft

7093: Gear set, transmission (includes 18T, 25T input gears, 13T idler gear (steel), 35T output gear, M3x13.75 screw pin)

7145: Spring, shock (GTR) (1.76 rate, orange) (1 pair)

7146: Spring, shock (GTR) (1.92 rate, green) (1 pair)

7147: Spring, shock (GTR) (2.06 rate, tan) (1 pair)

7148: Spring, shock (GTR) (2.22 rate, black) (1 pair)

7150: Half shafts, left or right (internal splined half shaft (2)/external splined half shaft) (2))/ metal u-joints (4)

7151: Driveshaft assembly (1) left or right (fully assembled, ready to install)/ 3x10mm screw pin (1)

7151X: Driveshaft, 1/16 E-Revo (steel constant-velocity) (assembled) (4)

7152: Slipper clutch, complete (includes slipper clutch hub, clutch pad, spring, 3.0mm NL, 1.5x6mm pin)

7360: Motor mount, finned aluminum (for 550 motors)

7379R: Cover, gear/motor plate access cover/ motor mount hinge post / 3x10mm CS w/split and flat washers (1) / 2.5x4mm CS (2) / 3x8mm BCS (1) (for 550 motors)

7380: Plate, motor (for 550 motor)