Results 1 to 25 of 25

Thread: Diff problems.

Hybrid View

  1. #1
    RC Racer
    Join Date
    Feb 2013
    Location
    Ashley, MI
    Posts
    165

    Diff problems.

    I have a 3903 brushless upgrade with the mm2 running 2s lipos. About every week I am breaking one of the two bearings in the rear diff. What is causing this to happen. It has gotten to he pont that I carry 2 extra diffs so when I'm in the field and it breaks I can replace them. Please post your advice on y this is happening .

  2. #2
    RC Turnbuckle Jr. Wolfslash16's Avatar
    Join Date
    Mar 2012
    Location
    Riverton Utah
    Posts
    4,373
    Are you running in dirt/sand? If so, the dirt might be getting into the bearing making them go bad really quick.
    Sl2sh Slayer Summit Sl4sh Teton/Rally T-Maxx Pnde

  3. #3
    RC Racer
    Join Date
    Feb 2013
    Location
    Ashley, MI
    Posts
    165
    Lately 60/20/20 (sand/dirt/gravel)

  4. #4
    RC Turnbuckle Jr. Wolfslash16's Avatar
    Join Date
    Mar 2012
    Location
    Riverton Utah
    Posts
    4,373
    Lately 60/20/20 (sand/dirt/gravel)
    Hmmm, my bet is all that sand driving is what killed that bearing. Do you have a picture of the bad bearings?
    Sl2sh Slayer Summit Sl4sh Teton/Rally T-Maxx Pnde

  5. #5
    RC Racer
    Join Date
    Feb 2013
    Location
    Ashley, MI
    Posts
    165
    Not much to take a picture of . All that's usually left is he outside and inside rings

  6. #6
    RC Turnbuckle Jr. Wolfslash16's Avatar
    Join Date
    Mar 2012
    Location
    Riverton Utah
    Posts
    4,373
    Sl2sh Slayer Summit Sl4sh Teton/Rally T-Maxx Pnde

  7. #7
    RC Champion
    Join Date
    Nov 2010
    Location
    United Kingdom of England land.
    Posts
    1,805
    If your breaking bearings every week, there is something not fitting correctly/ seals missing, or it's been sprayed with wd40.
    Guide books aren't part of the packaging.

  8. #8
    RC Racer
    Join Date
    Feb 2013
    Location
    Ashley, MI
    Posts
    165
    Ok what do u recommend using to grease the bearings

  9. #9
    RC Champion
    Join Date
    Nov 2010
    Location
    United Kingdom of England land.
    Posts
    1,805
    I just use lithium bearing grease from the local cycle shop, Left overs from when i do the bike's bearings.
    The original WD40 is a grease eater and not a lubricant. If you use this then you'll need to clean up the insides and use a grease afterwards.
    Although WD40 is a brand name there is many products under their belt, some lubricants, greases, rust eaters, de-greasers and more.
    Guide books aren't part of the packaging.

  10. #10
    RC Qualifier
    Join Date
    Jun 2012
    Location
    nevada, mo
    Posts
    288
    Quote Originally Posted by trax de max View Post
    I just use lithium bearing grease from the local cycle shop, Left overs from when i do the bike's bearings.
    The original WD40 is a grease eater and not a lubricant. If you use this then you'll need to clean up the insides and use a grease afterwards.
    Although WD40 is a brand name there is many products under their belt, some lubricants, greases, rust eaters, de-greasers and more.
    Will the lithium grease work in the tranny as well?

  11. #11
    RC Champion
    Join Date
    Nov 2010
    Location
    United Kingdom of England land.
    Posts
    1,805
    I forgot to add, the cycle bearing lithium grease is a lot more viscious, than what automotive lithium grease is.
    Guide books aren't part of the packaging.

  12. #12
    RC Turnbuckle Jr. Wolfslash16's Avatar
    Join Date
    Mar 2012
    Location
    Riverton Utah
    Posts
    4,373
    I use either marine grease if I run in wet places, or for dry/on road use I use 3 in 1 oil.
    Sl2sh Slayer Summit Sl4sh Teton/Rally T-Maxx Pnde

  13. #13
    RC Champion
    Join Date
    Nov 2010
    Location
    United Kingdom of England land.
    Posts
    1,805
    Is it not a bit time consuming changing bearings to run depending on if it's wet or dry conditions.
    Guide books aren't part of the packaging.

  14. #14
    RC Turnbuckle Jr. Wolfslash16's Avatar
    Join Date
    Mar 2012
    Location
    Riverton Utah
    Posts
    4,373
    Is it not a bit time consuming changing bearings to run depending on if it's wet or dry conditions.
    Ha ha ya, but that's not what I do... What I should have said is I use marine grease in the winter so I can drive in snow, and then I use 3 in 1 oil in the summer when I don't get my cars wet.
    Sl2sh Slayer Summit Sl4sh Teton/Rally T-Maxx Pnde

  15. #15
    RC Champion
    Join Date
    Nov 2010
    Location
    United Kingdom of England land.
    Posts
    1,805
    After i posted i figured that's what you do, In England we'll be swapping every day.
    Guide books aren't part of the packaging.

  16. #16
    RC Champion
    Join Date
    Nov 2010
    Location
    United Kingdom of England land.
    Posts
    1,805
    Is the problem resolved now gunamonkey.
    Guide books aren't part of the packaging.

  17. #17
    RC Champion
    Join Date
    Feb 2012
    Location
    Brookline, NH
    Posts
    1,206
    If you want to spend more time playing and less time replacing diffs get some 1/8th scale diffs. and get rid of the problem. The little 6x12 bearings don't hold up very good imo.

  18. #18
    RC Champion
    Join Date
    Nov 2010
    Location
    United Kingdom of England land.
    Posts
    1,805
    I don't put none in there. I just let that run as it is.
    I only grease the bearings and replace diff/shock fluids if it starts to not look right while driving.
    some greases eat plastic and makes it soft and moveable.
    Guide books aren't part of the packaging.

  19. #19
    RC Racer
    Join Date
    Feb 2013
    Location
    Ashley, MI
    Posts
    165
    Haven't broke a bearing since but I did destroy a diff last weekend. Wen I opened up the diff the drive gear was cracked,diff cup stripped, and all the Spyder gears destroyed. I was only running 4s. Luckily I had a raplacement diff to through in.

    -EMAXXBRUSHLESS
    Where can I find a 1/8 scale diff to fit in the stock bulkheads. Or a diff bulkhead set, that replaces all of that

  20. #20
    RC Champion
    Join Date
    Mar 2001
    Location
    Spring valley mn
    Posts
    1,135
    Quote Originally Posted by Gunamonkey View Post
    Haven't broke a bearing since but I did destroy a diff last weekend. Wen I opened up the diff the drive gear was cracked,diff cup stripped, and all the Spyder gears destroyed. I was only running 4s. Luckily I had a raplacement diff to through in.

    -EMAXXBRUSHLESS
    Where can I find a 1/8 scale diff to fit in the stock bulkheads. Or a diff bulkhead set, that replaces all of that
    http://www.fastlanemachine.net/prodd...LM17750&cat=15

    http://www.fastlanemachine.net/prodd...LM18750&cat=15

    I have been using the FLM Hybrids for years in both my BB T and Brushless E. Good stuff, haven't had a diff issue since.
    My tranny case is stock :D

  21. #21
    RC Champion
    Join Date
    Nov 2010
    Location
    United Kingdom of England land.
    Posts
    1,805
    It may of been weakened buy the bearing damage from previous runs, Hopefully when this is fixed it should last a lot longer. You can get metal diff carriers from flm I think.
    Guide books aren't part of the packaging.

  22. #22
    RC Racer
    Join Date
    Feb 2013
    Location
    Ashley, MI
    Posts
    165
    Not from the bearing damage because i completely replaced the diff after the bearings because I didn't want to have to deal with damage from breaking a bearing.

  23. #23
    RC Champion
    Join Date
    Nov 2010
    Location
    United Kingdom of England land.
    Posts
    1,805
    Do you shim the diffs
    Guide books aren't part of the packaging.

  24. #24
    RC Racer
    Join Date
    Feb 2013
    Location
    Ashley, MI
    Posts
    165
    No I don't shim the diffs

  25. #25
    RC Champion
    Join Date
    Nov 2010
    Location
    United Kingdom of England land.
    Posts
    1,805
    I think alot of people have put shims in the diffs and that helped them out. There is a decent write up about it on here somewhere.
    Guide books aren't part of the packaging.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •