Kawasaki e revo

[50togo]

Well they look nice but everyday we have been rained out. Looks like it will be dry tomorrow so I will charge up the batteries in the morning!

[mike-susieq1]

Suppose to be dry here for 4 days after tomorrow but too busy you enjoy the fun and sun. I got to run yesterday for about 15 mins on a partial charge only. Rain all the time lately

[50togo]

Maybe running tomorrow. Did a rookie move I was going to run 5cell in my merv but grabbed the parallel connector not the series hooked up my new thunder power 3s 65' and 2s 65 50c
Was ruddy to go but car started getting hot. So I yanked the batteries off they were warm. The 3cell went from 12.6vdown to 9.8v In a minuteand the 2cell was overcharged at 9.8 volts. So I ran the2 cell fast to drop voltage and so far its working fine

[Money pit]

Maybe running tomorrow. Did a rookie move I was going to run 5cell in my merv but grabbed the parallel connector not the series hooked up my new thunder power 3s 65' and 2s 65 50c
Was ruddy to go but car started getting hot. So I yanked the batteries off they were warm. The 3cell went from 12.6vdown to 9.8v In a minuteand the 2cell was overcharged at 9.8 volts. So I ran the2 cell fast to drop voltage and so far its working fine

It pays to double check things before plugging them in. I accidentally shorted the batteries on mine a long time ago, I have double checked everything from that point on. The bright side is that you probably will never do that again

[mike-susieq1]

ooh boy that was close for pricey lipos i would have kicked myself for weeks for that maybe longer lol. you have a very nice collection of lipos there i seen in a picture.

[50togo]

Yep! My new thunder power too 80.00 worth .
I.picked up this Hr bulkhead tie bar 6061 t6 cnc machined not stamped and aluminum rocker posts that save 16 grams by themselves!

[50togo]

Those HR cups looks sweet!

[Ghostbuster]

Can you say "Bullet proof differentials"?

[50togo]

I sure hope so!

[clp71220]

Yea I hope so too. We got lots of moneys in the Differentials.

[Ghostbuster]

Yea I hope so too. We got lots of moneys in the Differentials.

I bet... When I first ordered my erbe I bought two extra complete diffs... but I haven't had problems with mine yet thankfully.

[50togo]

Hopefully your luck lasts!
So far the robinson racing are holding up and I will meanwhile put the losi diff together

[Ghostbuster]

Hopefully your luck lasts!
So far the robinson racing are holding up and I will meanwhile put the losi diff together

Yeah I know! I think it is the combination of proper diff break in, mostly 4s use, and the axles are close to parallel with the ground. But yeah you should be set with all of your diff mods lol

[50togo]

I will run them and hopefully switch over to the losi before they are wasted so I can save the diffs for my e maxx!

[50togo]

Pulling off the castle quick connect doesn't work with the field link. What a waste of money!

Happy new year!

[50togo]

did some good bashing! click on photo

we decided to leave before we broke something and heading up the hill to get my bag heard the dreaded clicking sound! sounds like i smoked the spider gears again. time to get busy with the losi mod

[50togo]

does anyone know if they make a 5608 manual or are they all 5603?

[MITCH316]

here you go : 5608 Manual

[50togo]

Thanks. Mine being a Kawasaki edition shipped with the 5603

[MITCH316]

No worries mate .

[50togo]

I was just wondering. I seen one on ebay and it was for a 5608 but the picture is from a 5503

[50togo]

Kind of a bad landing on the jump. I couldn't see the landing where I was standing!

I just heard from the seller on ebay they said the 5608 comes with the 5603 manual. Can anyone confirm?

[aussiespud]

nice one nitro though bro

[50togo]

Thanks it was a lot of fun!

[50togo]

Looks are kind of deceiving. I have jumped 28 ft there with my merv and this jump was an easy ten ft past that one. Without getting much speed. I came down a hill from the right had to turn left straighten up and hit the jump

[Yip-man]

Kind of a bad landing on the jump. I couldn't see the landing where I was standing!

I just heard from the seller on ebay they said the 5608 comes with the 5603 manual. Can anyone confirm?

Got my new 5608 in September and it came with 5603 manual if that helps

[50togo]

thanks that's what i figured. guess you have to go online

[Yip-man]

thanks that's what i figured. guess you have to go online

Had me confused for a while after bought it, cos the manual was different.

Downloaded on to my ipad, started keeping all my manuals on it, everything from tv to toaster.

[50togo]

Yep mine is on my computer and galaxy 3 since I am always on it!

Look what came today! Hpp motor mount and wheel hubs!
Somehow made it all the way from Germany with a box that wasnt taped shut!
Looks like its all here even some candy!

[Yip-man]

Mmmmmm haribo


Edit: oh the other stuff not bad

[50togo]

Look at that pinion! I was hoping it was the spider gears!

[50togo]

Tearing it down!

[MITCH316]

Look at that pinion! I was hoping it was the spider gears!

You too hard on your truck mate ; evidence of a basher . Time for the Losi mod installation...good luck with it .

[50togo]

Yep! Didn't buy it to go slow!
Tomorrow I will start cutting and grinding!

[MITCH316]

Sweet...will be watching your progress mate .

[50togo]

I would say its a bad sign you spent too much on your cars when you earn 54.00 worth of ebaybucks!

[50togo]

finally got rolling on the losi diffs!

[50togo]

Looks are kind of deceiving. I have jumped 28 ft there with my merv and this jump was an easy ten ft past that one. Without getting much speed. I came down a hill from the right had to turn left straighten up and hit the jump

I measured it with a tape measure. I was close 35ft

[clp71220]

35 FEET Dude You need to fly airplanes. They can fly farther than that any day.
I got one of my diff. cups today.

[50togo]

They are sweet! Everything went pretty smooth hopefully tomorrow working on the bulkheads