Results 1 to 10 of 10
  1. #1
    RC Racer
    Join Date
    Sep 2002
    Location
    Roseville, MI
    Posts
    205

    New Image .12 engine parts

    Hello!
    I've been out of the RC world for around 5 years, but I'm back, and I've been studying the Vintage Traxxas models. I've got discontinued parts lists for them all if anyone is interested. Anyway, I've discovered a very interesting source for new Image .12 parts, from the original manufacturer. To read the following, use my explanation here.

    Discontinued Traxxas part number=original manufacturer's part number.

    These are parts that are identical to the discontinued Traxxas parts.
    3239=12124 Stud & nut, carburetor attachment
    3239=12118 Nut, carburetor attachment
    3241=12845 O-ring, idle mixture needle screw
    3242=12811 Nut, throttle lever
    3243=12812 Lever, throttle
    3244=12813 Rotor (carburetor barrel)
    3245=91814 Spring, rotor
    3247=12816 O-ring (I can't be sure of the color, mine was missing)
    3248=12817K Needle seat, idle mixture (I can't be sure, mine was broken and the internal piece was gone)
    3249=12818 Nuts, seat securing (2)
    3254=12832 Screw, idle speed adjust (w/ nut)
    3254=12837 Screw, throttle stop (w/ spring)
    3209=12102 Engine backplate (Eliminates recoil starter) (Requires electric starter) (I can't be sure, I've never seen a Traxxas one)
    3213=12111 Gasket, back plate
    3221=12110 Bearing, crankshaft (rear) (I recommend an upgrade ceramic bearing)
    3222=12101 Crankcase (w/o bearings) (says ASP on the front instead of IMAGE)
    3223=12109 Bearing, crankshaft (front) (I recommend an upgrade ceramic bearing)
    3225=12203K Sleeve, cylinder/ piston (matched)
    3226=12213K Wrist pin/ G-spring retainer (1)

    These are parts that will work on the Image .12, but are not identical to the originals.
    3240=12804K Carburetor assembly
    3246=12815K Body, carb
    3250=12861K Needle assembly, high-speed
    3250=12819K Nipple/ gasket
    3250=12848K Needle valve body
    3251=12833K Ratchet spring, high-speed needle

    These are parts that will only work with each other, not the originals.
    3270=12522K Assembled starter
    3274=12506K Backplate (uses 2.5x8mm cap screws, 12518)
    3275=12516K Starter shaft
    3211=12502K Bearing, one-way starter/ starter engagement housing

    I'm still researching if the crank and cylinder head are correct. I'll post them if they are in the near future.

    You can get these parts through here. The prices need to be converted from CZK Czech Koruna to your currency, but the parts are pretty cheap.

    Hope this helps!

  2. #2
    RC Qualifier
    Join Date
    Jun 2012
    Location
    Palisade Colorado
    Posts
    511
    Welcome back!

  3. #3
    RC Racer
    Join Date
    Sep 2002
    Location
    Roseville, MI
    Posts
    205
    Thanks John! Glad to be back! Things sure have changed in this world...

  4. #4
    RC Racer
    Join Date
    Sep 2002
    Location
    Roseville, MI
    Posts
    205

  5. #5
    RC Racer
    Join Date
    Sep 2002
    Location
    Roseville, MI
    Posts
    205

  6. #6
    RC poster
    Join Date
    Nov 2012
    Posts
    5
    Thanks for the info Kyle, i have just picked up a nitro hawk with original an Image .12 engine. I'm sure your info will be of use to me :-) the parts seam cheap too! 7.50 for piston and sleeve - cant complain at that price although i've just noticed they have none in stock :-(

  7. #7
    RC Racer
    Join Date
    Sep 2002
    Location
    Roseville, MI
    Posts
    205
    Glad someone can use it!
    I think they have none in stock because they just distribute the parts. You can contact them and see what's going on.

  8. #8
    RC poster
    Join Date
    Nov 2012
    Posts
    5
    Thanks Kyle, realised that after i posted and found a couple of suppliers in Czech Republic. Just need a con rod which i've ordered from the USA, every thing else seams ok.
    Had it running yesterday and it seams quick enough to me. Just need the steering bell cranks now as mine are worn - dont suppose anyone knows if there is an alternative part to #1943?

  9. #9
    RC Racer
    Join Date
    Sep 2002
    Location
    Roseville, MI
    Posts
    205
    Here are some.

  10. #10
    RC poster
    Join Date
    Nov 2012
    Posts
    5
    Thanks kyle, saved them in my watch list. I've reduced the play with PTFE tape for now and its made a difference, handles much better now, not sure how long it will last though :-)

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •