Results 1 to 4 of 4
  1. #1
    RC poster
    Join Date
    Jun 2012
    Posts
    8

    Setting Up T-Link with DTS-1 and Funny Car

    I THINK that I can assist those of you (like me at first) who are having considerable difficulty getting DTS-1/T-Link/Funny car to behave:

    I did not know where the instructions for linking and binding Start/Finish Consoles and connecting T-Link program were. The instructions are "hidden" in the T-Link program for binding/linking the two consoles:

    1. Connect TQi (transmitter) with iPhone/iPod and run the T-Link program.
    2. At the HOME screen go to GARAGE.
    3. At the GARAGE screen go to CONNECT.
    4. Press the question mark at the top of the screen.
    5. Boom! There is the tutorial for firmware updates, and binding/linking START/FINISH consoles.

    Now, assuming that you have successfully completed the binding/linking the two consoles here is the drill for getting the star/finish CONSOLES to be good neighbors with the T-Link program:

    1. Follow this sequence by rote:
    2 First, turn on the START CONSOLE.
    3. Then turn on the TQi (transmitter) and the T-Link program on the iPhone/iPod.
    4. See green DTS icon on upper right screen of T-Link program.
    5. See slow blinking GREEN LED on lane 1, second from bottome LED.

    The START CONSOLE is now talking the the T-Link program.

    6. Turn on the FINISH CONSOLE. It will NOT be linked yet to the START CONSOLE.
    7. Press and hold the SET button on the START CONSOLE until it blinks twice.
    8. Now the START and FINISH consoles are linked BOTH are talking to the T-Link program.
    (Note: see the green DTS icon on the upper right screen program on the START CONSOLE).
    9. BOTH LEDS (again, second from bottom LED's blink green slowly for lane 1 and 2 on the START CONSOLE.

    10. The blink yellow rotating LED's have gone out on the FINISH CONSOLE and
    11. The yellow SPEED TRAP LED on lane 2 of the FINISH CONSOLE blinks slowly.

    BEHOLD!! The START/FINISH CONSOLES are now talking with each other and the T-Link program. All functions/options of the two consoles are now available in the T-Link program.

    You can check this by:

    1. Go to Home>Garage>DTS icon in the T-Link program.
    2. Go to DIAGNOSTICS see the START/FINISH CONSOLE icons are not X-ed out. The are working.
    3. You can now set up the reflectors in the T-Link program if you wish.

    Note: If you are trying to set up the DTS-1 in your house, beware that carpet really screws up the alignment of the lasers for the reflectors.

    SEE THE FOLLOWING POST FOR GETTING THE FUNNY CAR TO TALK TO THE DTS-1 AND THE T-LINK PROGRAM AT THE SAME TIME. This allows you to use a single TQi with the DTS-1 program AND the funny car.

    I hope this might help somebody. I apologize in advance for any errors, typos. I did write this post while I was actually doing these instructions on my DTS-1/TQi. I was able to learn this be trial and error, and a little parley with Traxxas support.

  2. #2
    RC poster
    Join Date
    Oct 2012
    Posts
    4
    I have the DTS-1 as well as the Traxxas F.C. but I also have an RJ Speed elect. dragster with ALL Traxxas electronics including the TQI 2 channel transmitter with docking pad as well as the TQI 5 channel receiver....my question is, can I control the DTS-1 and this dragster with the same TQI 2 channel transmitter and docking base ? I have never seen this transmitter on the Traxxas products site.....I purchased it and the receiver from ebay and they work fine for my dragster ?
    Thanks in advance and
    GOD BLESS
    glenn

  3. #3
    RC Qualifier PeterV's Avatar
    Join Date
    Jul 2008
    Posts
    508
    Yes, you can operate the DTS-1 and drive your vehicle with one TQi transmitter (as long as it's Docking Base equipped and you're running Traxxas link on an iPhone or iPod touch, of course).

    No matter what you're doing with the DTS-1 via Traxxas Link, your TQi transmitter's trigger and wheel are "active' and will operate your car.

    Note that your TQi has to have been previously bound to the DTS-1 and your car, so it can then link to the car and the DTS-1 to control them both.

    Here's how to do it: http://traxxas.com/support/DTS1-Linking-Binding

  4. #4
    RC poster
    Join Date
    Oct 2012
    Posts
    4
    Peter;
    Thanks so much for your reply and help......The transmitter is currently bound to the dragster so I will inturn bind it to my DTS-1 and give it a go.....and yes I do have an I-Pod touch..
    Thanks again for the link and GOD BLESS
    glenn

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •