Whats YOUR 2wd Traxxas Slash Setup

[kennymonsta]

POST YOUR PICTURES BELOW!

[smallwallman]

VXL Brushless with venom 2 cell 5000MaH 20c 7.4v. Traxxas Bfg on the front proline street fighters on back. I also put my extra Bfgs on the back for dirt

[smallwallman]

And my paddles for the dunes

[kennymonsta]

that looks like a good bashing setup if you have the right gearing

[chillij715]

Stockish class, set-up for carpet figure 8. Brushed, 19/86 gearing, 4400 lipo, stock tires, 1/4'' shock limiters in front,no pre-load springs,80 wt shock oil all around. 5.40lbs, sticky fingers tire compound, and heavy bearing grease in diff.

Just started racing, raced 4 races so far,sat night was last night of indoor, placed first in b-main,bumped up and got 4th in a-main.first place did 54 laps in 6min I did 50.
Pic is with my basher body, just got done playing in the dirt. Basher by day, racer by night
[IMG][/IMG]

[smallwallman]

It is a good basher set up I am going to
a local track this week just to try it out

[kennymonsta]

thats awesome! if it works out good let me know on this thread

[smallwallman]

Ok I will try

[Kansei]

2wd Slash VXL on gens ace 30c 2s , 25/86 gearing . Proline protrac suspension with Traxxas big bore shocks , GH alloy trans case (heavy grease in diff), TRX alloy caster blocks , 4x4 axles , Proline split six wheels with Trenchers , Proline Desert rat carnage ed. body , rpm bumpers with low profile wheelie bar kit . Think thats it LOL

[DBG]

Slash 2wd, VXL system with 2(parallel) 8.4V 3000mah Ni-MH = 8.4V 6000mah Ni-MH battery, original tires, original body, gearing: 90 23, and water cooled.

[Cherry2000]

Lets see.

Started out with a 5803. Installed a MMP and Trinity revtech 10.5 motor.Was running 3cell but had some heat problems so went to 2cell now running an aluminum gear case and back to the 3cell on a 19 pinion 90 spur and running cool. Upgraded the shock towers with integy fiberglass ones front and rear. Traxxas aluminum knuckles front and rear and aluminum caster blocks. Big bore traxxas shocks. Using an old FM jr xs3 radio. Ya its old school but it works great and has a ton of adjustments. Running stock traxxas tires just because they work for me and there cheep. That's about it just a few thing left Id like to do.

[judgegixxer]

Too much to list....or justify.
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG][IMG][/IMG]

[IMG][/IMG]

[Slash 2wd]

alot to name but i went for a taler ride height and stability



Front

Rear

[deerhurst]

Well it used to be a slash.

[kennymonsta]

Judgegixxer, where did you get the led lights and the metal frame, please message back...

thanks for your time

[judgegixxer]

Judgegixxer, where did you get the led lights and the metal frame, please message back...

thanks for your time

I lucked out... the led lights are from some type of losi truck and were in a bargain clearence bin at a hobby shop. The cage was on display at a different hobbyshop but no bargain. I couldn't leave without it. It's made by VG racing.

[kennymonsta]

what kind of gearing is good for high speed on dirt/gravel and flat road

[Wolfslash16]

What's my slash's set up? BONE STOCK!!! It's been stock for the entire 4 months I've had it with NO broken parts. I just havn't found a reason to replace anything on my slash so far. Well, maybe a brushless motor would be nice though...

[redlightrandy]

i think 10-11 final drive ratio is good for speed. i got 10.15 now. oh and wolf slash... when you go brushless you will eventually break something. lol. first thing you will probably break is either a caster block, hub carrier, or control arm. good thing they are cheap though.

[Wolfslash16]

Ok, I just don't know if $150 is worth it for getting a V brushless setup... I mean $150 would buy a nice big block for my slayer...

[Power Up]

No pcs yet just got Slash 2wd last week .took off training mode and changed pinion today.....

[damir009]

[redlightrandy]

[IMG][/IMG]
here is the only pic i have right now of my 2wd slash. and yes it is towing a broke rc mustang gt. lol. specs are as follows.

vxl/velinion esc and motor
rpm front and rear arms
rpm motor protector
rpm hub carriers
strc lcg
strc bulkhead
anza hinge pin set
anza front tie bar
32 pitch gears-15 pinion 56 spur(54 mph top speed)
2s ******* ******** 4000mah 40-80c(for track)
3s venom 5000mah 20c for bashing
for wheels and tires i got stock front and rear, rear bowfighter m3 compound on proline wheels, front proline bowtie m2 compound on proline wheels, and rear proline trenchers m3 compound. everything else is stock.

[Agriganosa]

Sorry i dont have a picture of my slash, i mean i do, but i dont know how to upload pictures here, anyways
Mine is build for speedruns and does about 70mph with 3s.
Geared 31/76, piggyback shocks all around with integy heavy duty springs and 60w oil all around, RPM almost everything.
Streetfighters all around, LCG kit, i assume that soon ill do something with my tranny cause stock tranny seems to be falling appart at 65+mph

[turok]

the one in the picture is still a project in progress. but i also have another sand slash with bug body + protrac kit all round. also another 2 with most parts replaced with alloy. but i don't really want to use them. lol

almost forgot i changed my rustler to a low slash on roader with a STRC lgc kit. that can be used with some kyosho 1/8th bodies that i have.

[RByers]

I'll have to get a pic. Been a while since I've ran my trucks but getting back into it. As it sits now after some new things.
VXL combo
Integy Aluminum transmission, and piggyback shocks all around
Rpm bumpers, slid plates, arms, strut towers, nerf bars, and whole rear bumper set up
Traxxas aluminum castors
Avid rc bearings
Currently running a new set of switch tires on proline 2.2/3.0 bead locks
******* 2s and 3s batteries.
Tower hobbies 2.4 tx/rx

I'll get a pic up shortly.

[RByers8252]

I'll have to get a pic. Been a while since I've ran my trucks but getting back into it. As it sits now after some new things.
VXL combo
Integy Aluminum transmission, and piggyback shocks all around
Rpm bumpers, slid plates, arms, strut towers, nerf bars, and whole rear bumper set up
Traxxas aluminum castors
Avid rc bearings
Currently running a new set of switch tires on proline 2.2/3.0 bead locks
******* 2s and 3s batteries.
Tower hobbies 2.4 tx/rx

I'll get a pic up shortly.

Found my original account

[kennymonsta]

come on guys more pics! lol

[Agriganosa]

My whole collection so far

[judgegixxer]

[IMG][/IMG]

[momort]

tacon 3660 1800kv,traxxas anaconda tires,mip cvds,xerun 80amp esc,proline raptor svt body,3s 5000mah 40c lipo,26/50 gearing gps 48mph and some other proline and rpm upgrades

[kennymonsta]

judgegixxer i bought the dynamite skidplates that you have for my slash and the back one will install easy but the front one wont install because the little post that come with the dynamite set wont go into the plastic bell crank thingy because the screw wont screw into the metal post, i can only get it to go in half way, i am sorry if i am confusing you can you please reply back,

thanks so much

[judgegixxer]

judgegixxer i bought the dynamite skidplates that you have for my slash and the back one will install easy but the front one wont install because the little post that come with the dynamite set wont go into the plastic bell crank thingy because the screw wont screw into the metal post, i can only get it to go in half way, i am sorry if i am confusing you can you please reply back,

thanks so much

I already had the GH Racing Aluminum bellcrank etc before I mounted those skids. Never tried them with the stock setup. I remember i had to shim the GHposts to get the linkage to turn smoothly on bearings but I either used the GH racing screws or the dynamite ones whichever fit I can't remember. I might have even used some other screws I had. It's been quite awhile since I've had to tear down that section.

[kennymonsta]

ok well thanks i got it to work turns out i wasn't using the right screw, lol

[Dr. Isotope]

Mid Motor Slash

Wheels/Tires:
AKA 17mm adapters
AKA 1/8th dish wheels with JConcepts green Subcultures

Chassis:
Custom aluminum/G10 chassis, 13.0" wheelbase

Suspension:
Front: Traxxas Big Bores, RPM green 2-stage pistons, 40wt, Losi green 2.0" springs
HPI Blitz ESE rod ends, 3Racing 4.8mm screwstuds, Associated 50mm Ti turnbuckles
Dr. Isotope custom G10 front shock tower
Venom aluminum bulkhead

Rear: Traxxas Big Bores, RPM purple 2-stage pistons, 35wt, Losi silver 2.5" springs
HPI Blitz ESE rod ends, HPI 4.8mm steel ballstuds, Associated 50mm Ti turnbuckles
RPM rear shock tower

STRC locknut hinge pins

Steering:
Slash 4x4 bellcrank
VP Pro 30mm servo horn
Savox 1257tg (0.07sec/60º, 139oz/in)
HPI Blitz ESE rod ends, 3Racing 4.8mm screwstuds, Associated 50mm Ti turnbuckles
Traxxas aluminum caster blocks
RPM steering knuckles

Protection:
ProLine front bumper
RPM front bodymount
RPM rear bodymount
SC10 4x4 rear bumper
custom mudflaps
custom rear skidplate
custom under-chassis graphic w/ UHMWPE protector

Drivetrain:
Castle Creations Mamba Max Pro
Castle 1410Y 3800kv motor
STRC layshaft, Associated V2 slipper, JConcepts Silent Speed spur, 25/84p gearing
Tekno M6 driveshafts w/ Tekno 17mm adapters
Tekno 1.5º bearing carriers

[adonismp82]

Mid Motor Slash

Wheels/Tires:
AKA 17mm adapters
AKA 1/8th dish wheels with JConcepts green Subcultures

Chassis:
Custom aluminum/G10 chassis, 13.0" wheelbase

Suspension:
Front: Traxxas Big Bores, RPM green 2-stage pistons, 40wt, Losi green 2.0" springs
HPI Blitz ESE rod ends, 3Racing 4.8mm screwstuds, Associated 50mm Ti turnbuckles
Dr. Isotope custom G10 front shock tower
Venom aluminum bulkhead

Rear: Traxxas Big Bores, RPM purple 2-stage pistons, 35wt, Losi silver 2.5" springs
HPI Blitz ESE rod ends, HPI 4.8mm steel ballstuds, Associated 50mm Ti turnbuckles
RPM rear shock tower

STRC locknut hinge pins

Steering:
Slash 4x4 bellcrank
VP Pro 30mm servo horn
Savox 1257tg (0.07sec/60º, 139oz/in)
HPI Blitz ESE rod ends, 3Racing 4.8mm screwstuds, Associated 50mm Ti turnbuckles
Traxxas aluminum caster blocks
RPM steering knuckles

Protection:
ProLine front bumper
RPM front bodymount
RPM rear bodymount
SC10 4x4 rear bumper
custom mudflaps
custom rear skidplate
custom under-chassis graphic w/ UHMWPE protector

Drivetrain:
Castle Creations Mamba Max Pro
Castle 1410Y 3800kv motor
STRC layshaft, Associated V2 slipper, JConcepts Silent Speed spur, 25/84p gearing
Tekno M6 driveshafts w/ Tekno 17mm adapters
Tekno 1.5º bearing carriers

How do you like the mid motor setup? I am thinking about getting the Slice A4?

What do you have to do to get the Associated V2 slipper install, do you have pictures?

[dgudenau]

My Slash has:
-Anza LCG Chassis
-Castle Creations Mamba Max Pro esc with Velineon 3500 motor
- Spektrum DX3C system
-Savox 4096 digital servo
-Hot Racing graphite transmission case with aluminum motor mount
-Losi ten scte front shocks (27.5 oil/red rate springs) Traxxas big bore rear shocks (27.5 oil/orange rate springs)
-STRC aluminum caster blocks
-RPM a-arms (front/rear), bumpers (front/rear), bearing carriers (front/rear)
-23 tooth pinion/90 tooth spur
-Panther switches short course tires
-JConcepts Ford raptor shell