+ Reply to Thread
Results 1 to 10 of 10

Thread: Squeilling?????

  1. 04-11-2012 04:03 PM #1
    e-revoPCB
    e-revoPCB is offline
    RC Racer
    Join Date
    Feb 2012
    Posts
    212

    Squeilling?????

    i changed my rear control arm last night i took the back of the trans/diff case off the gear came out so i just pushed it right back in no problem get the truck back together and it squells??? what could be my issue .....it doesnt squell when idle its just under slighty and heavy power... HELP!!!!!!!!!!!!!!!!!!!1
    Reply With Quote Reply With Quote
  2. 04-11-2012 04:09 PM #2
    e-revoPCB
    e-revoPCB is offline
    RC Racer
    Join Date
    Feb 2012
    Posts
    212
    were could this be coming from????
    Reply With Quote Reply With Quote
  3. 04-11-2012 04:22 PM #3
    e-revoPCB
    e-revoPCB is offline
    RC Racer
    Join Date
    Feb 2012
    Posts
    212
    and looked it over but why???? is my tranny done for if i dont find sqeel
    Reply With Quote Reply With Quote
  4. 04-11-2012 06:10 PM #4
    forbes
    forbes is offline
    RC Champion
    Join Date
    Oct 2007
    Location
    Plano Texas
    Posts
    2,241
    Send a message via Skype™ to forbes
    never had one squel... it's pretty much all plastic in there. unless you got the tranny shaft cocked in the bearing or you have a bearing going bad
    Reply With Quote Reply With Quote
  5. 04-11-2012 06:55 PM #5
    e-revoPCB
    e-revoPCB is offline
    RC Racer
    Join Date
    Feb 2012
    Posts
    212
    Quote Originally Posted by f0rb3s View Post
    never had one squel... it's pretty much all plastic in there. unless you got the tranny shaft cocked in the bearing or you have a bearing going bad
    how would i go about looking for that were is the tranny shaft
    Reply With Quote Reply With Quote
  6. 04-11-2012 07:18 PM #6
    forbes
    forbes is offline
    RC Champion
    Join Date
    Oct 2007
    Location
    Plano Texas
    Posts
    2,241
    Send a message via Skype™ to forbes
    when you take the back cover off you will see 2 bearings.. make sure they are in straight
    Reply With Quote Reply With Quote
  7. 04-11-2012 07:35 PM #7
    e-revoPCB
    e-revoPCB is offline
    RC Racer
    Join Date
    Feb 2012
    Posts
    212
    Quote Originally Posted by f0rb3s View Post
    when you take the back cover off you will see 2 bearings.. make sure they are in straight
    if they wernt it would act funny huh? going to do so now anything else to check for while im in surgery
    Reply With Quote Reply With Quote
  8. 04-11-2012 08:11 PM #8
    e-revoPCB
    e-revoPCB is offline
    RC Racer
    Join Date
    Feb 2012
    Posts
    212
    you push the gear all the way in and the bearing are straight any other suggestions
    Reply With Quote Reply With Quote
  9. 04-11-2012 08:21 PM #9
    e-revoPCB
    e-revoPCB is offline
    RC Racer
    Join Date
    Feb 2012
    Posts
    212
    you push the gear all the way in and the bearing are straight any other suggestions
    Reply With Quote Reply With Quote
  10. 04-12-2012 02:14 AM #10
    Mind_Reader7
    Mind_Reader7 is offline
    RC Qualifier
    Join Date
    Apr 2011
    Posts
    527
    Are you sure it's not the clutch bell and spur gear?
    Reply With Quote Reply With Quote
« Previous Thread | Next Thread »

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts

Forum Rules