This is my jato!
Last edited by andreadido; 05-10-2011 at 01:28 PM.
Team Weapon X Jato's:
Team Weapon X
For Bashers, By Bashers– http://www.BigSquidRC.com
my jato 3.3. sure do miss it
slammed the jato today..... Helped with the wheelies quite a bit.....
2K11 Nitro Monster Truck Champ Tmaxx 3.3
Some fun shots of my Jato. I'm driving and my wife is shooting the photos.
hey guys, lots of nice looking trucks here, thought id post some pics of my passed jatos and my present jatos
this is the jato i am working on now
before - http://i1238.photobucket.com/albums/...-40-10_632.jpg
after i switched my motor and electronics to my new roller -
these are 2 of my jatos i had before, sold them both.. the one with aluminum upgrades was one of the nicest ones i have had.
Just thought I would post some pics of my jato done loads of bits to it and very happy with it now.
this is my 3.3 stock not broken in yet finly found where i can buy fuel
sorry about pic quality taken from phone
I picked this guy up yesterday. It's a 2.5 had a bad motor but strapped a running one on it and it's good to go
Powder coated frame
My 2.5 and my friends 3.3
Last edited by Jato has ballz; 12-28-2011 at 09:34 PM.
FInally I finished painting my new body, it has it's little imperfections, but i think it's pretty sweet
My Jato... still waiting on some rpm arms all the way around and the matching front tires.. but here it is so far..
my jato with a novarossi 2.5 supercharged
Figured I'd put her up here. Aluminum upgrades, OS .21tm engine, ported pipe. Fun truck.
Last edited by usmiljtw22; 02-02-2012 at 02:53 AM.
My axial .32rr-1 powered Jato. Currently waiting on a 34 ford truck body that my buddy is airbrushing. Though it's probably going to be a pain to fit on the chassis.
RPM arms all around
RPM Front Bumper
Hot Racing Front and Rear Shock Towers
Hot Racing Front Body Mount
Hot Racing Dual Disk Brake Kit
Hot Racing Hardened Steel Transmission Gears
New Era Models Big Block conversion Kit
New Era Models Chassis Brace
New Era Models Big Block Header
Ofna Jammin JP-3 Pipe
20/40 Revo Gears
Axial .32rr-1 engine.
Integy front and rear shocks
Traxxas red aluminum Turnbuckles
Golden Horizons Bulkhead
Dual Stage Air Filter
And a few other misc things.
Last edited by Acqua; 02-05-2012 at 09:42 PM.
Jato nickname Nightfox
Jato 3.3 Upgrades:
1. Integy Bell Crank
2. Integy Front Shock Towers
3. Integy Trans Support
4. Integy Brake Cam
5. Integy Roll Cage ( Have to use spaces to make fit around 3.3 engine, it fits either the 2.5 or 3.3 but with the 3.3 being taller adjustments are needed to fit)
6. Integy Air Filter Housing
7. M.I.P Rear CV Axles
8. Golden Horizons Steering Arms
9. Golden Horizons 30 Degree Caster Blocks
10. New Era Rear Shock Towers
11. New Era Front Camber Plate
12. New Era Top Chassis Support
13. Traxxas Mid-High Range Dual Chamber Pipe
14. Traxxas Blue Spindles
15. EZ Clamp Set
16. Traxxas Dished 2.2 Wheels
17. Proline Dirt Hawg and Proline Edge Tires
18. Traxxas GTR Teflon Aluminum Shocks.
Heres my Jato, even slid the Big Joes over the stock wheels ha.
Pro-Line crowd pleazer body (airbrushed), ported 3.3 engine, 56t spur gear, Pro-Line 2.8 desperado wheels with trencher tires, integy roll cage, rpm blue a arms.
Decided to get a little dirty...
My jato. Painted myself
Beatings will continue until compliance is gained
Blue Thunder always steals the show. I love this car.
Traxxas Jato 2.5 w/ 2.4 ghz radio:
Trx 3.3 engine
Traxxas low-end Exhaust pipe
Motorsavers air filter
2075 Hi-Torque throttle/steering servos
Rpm Front A-Arms
Rpm Rear A-Arms
Rpm Front Bumper
Traxxas steel cvd driveshafts
Traxxas red aluminum turnbuckles
Traxxas silver aluminum rear wheel knuckles
Traxxas Silver Aluminum front wheel Knuckles
Golden Horizons Blue Aluminum front wheel steering arms
Golden Horizons Blue Aluminum front shock tower
Golden Horizons Blue Aluminum rear shock tower
Golden Horizons Blue Aluminum front bulkhead
Golden Horizons Blue Aluminum brake/throttle linkage
Integy Blue Aluminum wheelie bar
Integy Blue Piggyback Shocks
Hot Racing Dual Brakes
Blue Aluminum Fuel Filter
Last edited by trxjato2.5; 04-08-2012 at 08:49 PM.
I am in the process of replacing all the screws with some stainless steel cap head screws. Those stock screws are a pain and strip out too much for me, plus I like all the ways you can finish off these type of screws, Thank you Hot Racing for some nice finishing touches. Example attached. I love my Jato!
RPM A-Arms all around
RPM front bumper
Hot Racing Brake
Proline Badlands Tires
20t clutch bell
pull start (EZ-start broke)
Getting a traxxas single chamber pipe soon
Forums Hi, sorry but I do not speak English, I wanted to introduce myself but I do not know where to do it as soon as I find out I will ...
however this is only for my Jato brakes crafts made by me earlier, this machine is too fast and you can not stop with just the rear brakes ....
...and a little treat
Thanks for your attention and see you soon ....
Just cut and painted this body for my Jato. Its the Stampede F-150 body. Yes, I cut the sides a bit high, but you live and learn =)
Jato 3.3 - Losi Micro-T - The Frog
Box Stock Jato 3.3 hitting 61mph already with more to go.
Hey everyone , im new to the whole forum thing but love rc's I have tons of pic's all of them but since this is all about the
Jato here are my pics from my collection of Jato RC's, thanks and ill answer any qustions in regards to mods and customizing bodies . I have drag racing video at the track, Smoking a brushless rusler with 68 chevy truck body on it.
Hope you enjoy!!!!!! let me know what you think
Last edited by Double G; 06-24-2012 at 07:51 PM. Reason: language
Tmaxx w 3.3
Slash ultimate hooked up
Playing in the snow
Beatings will continue until compliance is gained
I'm a newb. He's what I have done so far to my Jato that I just got a few weeks ago.
The wife has named the new Jato "The Other Woman."