Search:

Type: Posts; User: cubsfan2010

Page 1 of 20 1 2 3 4

Search: Search took 0.06 seconds.

  1. Replies
    2
    Views
    728

    Bad idea. Like Traxximus said you will get just...

    Bad idea. Like Traxximus said you will get just as much power out of a single Dewalt. Stock ESC won't run it either. Voltage is too high. Lastly it would be a lead sled with all the extra...
  2. You don't need to worry about cooling the lipo's,...

    You don't need to worry about cooling the lipo's, so go ahead and stuff foam in the vents. If your lipo's get hot then your C rating is too low.
  3. Replies
    14
    Views
    6,186

    Easier than the front. No issues.

    Easier than the front. No issues.
  4. Replies
    11
    Views
    683

    Reverse failure when wet is very common, but...

    Reverse failure when wet is very common, but yours went a step further. Some EVX2s do really well with water and some don't. It's a crap shoot. Also make sure to turn off the EVX2 by unhooking the...
  5. Thread: bulkheads!

    by cubsfan2010
    Replies
    6
    Views
    399

    Most hobbyshops don't have a clue about the...

    Most hobbyshops don't have a clue about the products they sell. Bulks are easy. First time can be a bit tricky, but once you see how everything goes together they are easy after that. Like AoD...
  6. Replies
    5
    Views
    1,373

    Single 4s battery??? You mean a pair of 2s lipos...

    Single 4s battery??? You mean a pair of 2s lipos in series. Bare minimum amp rating of 120 amps continuous, but more is always better. The 5000 40c is a great suggestion and will provide plenty of...
  7. Replies
    3
    Views
    504

    Anyone see Extreme 4x4 on TV

    They did a full scale copy of the Revo/Summit suspension setup. They used a Summit to show there plans for the 'Curvy Buggy' project. Be interesting to see how it works in full scale when done.
  8. Replies
    17
    Views
    1,291

    I run one on my Tekin powered ERBE. It does...

    I run one on my Tekin powered ERBE. It does work, cools things down, and was easy to install. Just fits over the motor can and 2 zipties hold in place. Plug power lead into a open spot on your Rx....
  9. Common issue with MMM. Switch is weak and fails...

    Common issue with MMM. Switch is weak and fails often. Your lucky as most fail in OFF position. Just cut the switch off and connect the two wires together to hard wire it on all the time.
  10. Thread: Mattracks

    by cubsfan2010
    Replies
    5
    Views
    1,304

    That is all the cheap Radio Shack stuff. They...

    That is all the cheap Radio Shack stuff. They will work, but will break quickly under the stress of a heavy truck like the Summit. Best to wait for the good ones and run snow chains in the meantime.
  11. Replies
    6
    Views
    264

    Did you get your ESC wet? Common problem with...

    Did you get your ESC wet? Common problem with EVX2 if it gets moist. Generally fixes itself once dried out.
  12. Replies
    13
    Views
    1,984

    That's why you go Tekin.:cool::cool:

    That's why you go Tekin.:cool::cool:
  13. Replies
    13
    Views
    1,984

    AoD's gearing sounds like a good starting point. ...

    AoD's gearing sounds like a good starting point. I've heard good things about Xerun ESC's, but the motors are not as good. Pairing the Xerun with a Neu/Castle motor is a nice combo. I still got to...
  14. Replies
    39
    Views
    2,821

    Latest version has throttle bugs. Go back to the...

    Latest version has throttle bugs. Go back to the previous version you were running and see if it fixes it.
  15. Replies
    45
    Views
    1,953

    22/58 seriously??? That's geared for 80 mph on...

    22/58 seriously??? That's geared for 80 mph on 6s!:eek: I would consider that crazy high gearing.
  16. Replies
    2
    Views
    1,027

    Wrong voltage cutoff won't hurt the ESC, but...

    Wrong voltage cutoff won't hurt the ESC, but running NIMH can. Ditch the NIMH and only run lipos capable of at least 120 amps continuous with the MMM. Set the cutoff for 3.4v/cell.
  17. Replies
    15
    Views
    6,994

    Sounds like a Rube Goldberg way of getting the...

    Sounds like a Rube Goldberg way of getting the same power of 1 Dewalt. Never mind that the Dewalt can also handle 5s lipo voltage, 775 can't, for serious power.
  18. Replies
    2
    Views
    1,075

    I'm running 75k front and 60k rear. Get a little...

    I'm running 75k front and 60k rear. Get a little unloading, but not bad. Most times all four will spin. My diffs are shimmed up pretty tight as well, so that helps.
  19. Thread: Tekin T8's

    by cubsfan2010
    Replies
    15
    Views
    3,316

    Make sure you choose the 4038 motor. KV depends...

    Make sure you choose the 4038 motor. KV depends on the # of lipo cells you plan to run. 2250 or 2000kv for 4s, 2000 or 1700kv for 5s, 1700 or 1400kv for 6s.
  20. I used to run 2s 5800's and 6000's in my 12V...

    I used to run 2s 5800's and 6000's in my 12V Dewalt Erevo and would only get about 20 minutes of very hard bashing. Going more slowly i would get 30-40 minute runs.

    5000 mah 20C is a tad on the...
  21. Replies
    17
    Views
    631

    With a 14t pinion and 68t spur, assuming stock...

    With a 14t pinion and 68t spur, assuming stock tires, your geared for 42 mph! That is too high. ERBE's running 4s with twice the watts in a MMM only gear that high. Gear it down to 12t pinion...
  22. Replies
    17
    Views
    631

    Sounds like your running NIMH, or very weak lipo,...

    Sounds like your running NIMH, or very weak lipo, and they can't handle the amp load at full throttle. Either the LVC is kicking in or the BEC is being starved for power. Get better batteries or...
  23. Replies
    9
    Views
    1,677

    I used a piece of lexan cut to fit into the screw...

    I used a piece of lexan cut to fit into the screw holes of my old EVX2. Then I mounted the RX8 to it using the included mounting screws and template for drilling holes to line up with the mounting...
  24. Replies
    12
    Views
    1,244

    Don't worry about the included charger not being...

    Don't worry about the included charger not being in the box. They are awful and take forever to charge a battery. Skip the Onyx 240 as well since it won't charge lipo. NIMH is a dieing technology....
  25. Replies
    14
    Views
    1,923

    ERBE and Revo 3.3 are not the same. The ERBE is...

    ERBE and Revo 3.3 are not the same. The ERBE is stronger with a extra I bar. A ERBE will tear up a 3.3 diff.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4