Search:

Type: Posts; User: Traden13

Page 1 of 3 1 2 3

Search: Search took 0.15 seconds.

  1. Replies
    16
    Views
    296

    would the 4600 kv be too high for the pede on 3s?

    would the 4600 kv be too high for the pede on 3s?
  2. Replies
    16
    Views
    296

    That sounds good. Im assuming that the facts...

    That sounds good. Im assuming that the facts stated above hold true or mostly true for the castle 4600 motor which is what I am leaning towards.
  3. Replies
    16
    Views
    296

    I dont know all of the specifics but the tenshock...

    I dont know all of the specifics but the tenshock motor draws more current than the stock velineon. A high c rating battery is required to provide for the motor.
  4. Replies
    16
    Views
    296

    Thanks. What if i used the hobbywing sc8 esc...

    Thanks. What if i used the hobbywing sc8 esc then got the castle 1406 4600 kv? I found that for about the same price and i know that it doesnt have the same power as the tenshock but that doesnt...
  5. Replies
    16
    Views
    296

    That seems like a pretty good combo for the...

    That seems like a pretty good combo for the money. I was thinking about selling my esc with the cooling fan and putting that towards some of a new system. Any problems installing this combo?
    ...
  6. Replies
    16
    Views
    296

    Dead motor! new electronics?

    My stock velineon motor is no longer working:mad: The truck is over a year old and I still need to call traxxas but I am not expecting them to be able to do much about it. I need a new motor...
  7. Is there any way I can rebuild it or would i need...

    Is there any way I can rebuild it or would i need an entirely new motor?
  8. Ive discovered that it is the motor that is...

    Ive discovered that it is the motor that is causing all of these issues. When any load is applied even just turning the wheels when they are off the ground caused the shaft to not spin while...
  9. when free revving the motor, it works just fine...

    when free revving the motor, it works just fine but with any load, it all goes wrong. I put the car on the ground after re assembling everything and looked at the center driveshaft while giving it a...
  10. The pinion and spur look fine, and all of the...

    The pinion and spur look fine, and all of the wheels turn smoothly. There was alittle bit of sand on the driveshafts but I cleaned that off.
  11. So I should hold the pinion gear stationary and...

    So I should hold the pinion gear stationary and rev the motor? sorry i wasnt sure what "snug it up" means.:)
  12. Is there any way I could test to see if the...

    Is there any way I could test to see if the problem is the motor?
  13. car stopped moving and very bad grinding noise!

    I was driving in a sandy field having a great time for about 10-15 minutes and then all of the sudden the car just slowed down without me doing anything and stopped. When I walked up to it and tried...
  14. thanks for the advice! I will need to get some of...

    thanks for the advice! I will need to get some of that but the MIP's are brand new. so i dont feel like the problem is coming from the driveshafts.
  15. weird clinking noise! Mysterious binding/friction

    I just installed my MIP cvd's on the front yesterday and took it out for the first time with them on. The
    truck flipped over on its roof and the wheels were still spinning alittle but only the two...
  16. Replies
    10
    Views
    624

    Definitely get the mip's. When I ran 3s it just...

    Definitely get the mip's. When I ran 3s it just shredded the stock driveshafts and with the trenchers ive found it makes the problem even worse and it introduces the problem to the front. I...
  17. Replies
    15
    Views
    524

    Thanks guys im leaning towards the mips for the...

    Thanks guys im leaning towards the mips for the front I just want to make sure they wont bind too much with the alluminum c hub and steering block. Does anyone know about this?
  18. Replies
    15
    Views
    524

    sorry steering block and c-hub.

    sorry steering block and c-hub.
  19. Replies
    15
    Views
    524

    If i do go out and get the front mip's would i...

    If i do go out and get the front mip's would i have to do anything to make them work with my alluminum steering block and bearing carrier in the front?
  20. Replies
    15
    Views
    524

    I have found the mip c-cvd's and they are alot...

    I have found the mip c-cvd's and they are alot cheaper than the xduty cvd's. do they work for the front? I dont see why they wouldnt based on pictures.
  21. Replies
    15
    Views
    524

    Front driveshaft options??

    A while back I switched to 3s and immediatly snapped multiple rear stock drivesharfts. Eventually I switched to MIP's in the rear but not the front because I hadn't had any trouble with those. ...
  22. Thread: new servo

    by Traden13
    Replies
    4
    Views
    330

    thanks:) would this work?...

    thanks:) would this work?
    http://www.savoxusa.com/Savox_SC1258TG_Digital_Servo_p/savsc1258tg.htm
    it looks like enough torque and plenty of speed but it costs less that the ace one.
  23. Thread: new servo

    by Traden13
    Replies
    4
    Views
    330

    new servo

    So ive been driving my truck for a while and have decided that the stock servo isnt quite performing to my standards. it isnt centering as well as i would like so what would be a good servo that i...
  24. Replies
    6
    Views
    510

    I use the rpm front bumper and it works great. I...

    I use the rpm front bumper and it works great. I ran it off a 40 foot jump and it went straight into a 4 inch tree right on the front of the car and nothing broke. it has saved me multiple times.
  25. Replies
    37
    Views
    1,031

    a rock or something is stuck up in the center...

    a rock or something is stuck up in the center drive shaft cover?:confused:
Results 1 to 25 of 53
Page 1 of 3 1 2 3