Search:

Type: Posts; User: nitroboy2

Page 1 of 6 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    13
    Views
    407

    I'll try re-building the engine using the link...

    I'll try re-building the engine using the link you sent me and see how it goes, I have all winter anyways :D

    Thanks for your help.
  2. Replies
    13
    Views
    407

    How did you fix it?

    How did you fix it?
  3. Replies
    13
    Views
    407

    Yeah, tried that...I even took the needle out and...

    Yeah, tried that...I even took the needle out and put it back in.
  4. Replies
    13
    Views
    407

    Yes, fuel is getting in..

    Yes, fuel is getting in..
  5. Replies
    13
    Views
    407

    Truck wants to quit on me.

    Was out with the 3.3 yesterday. Everything was running great, popping wheelies, good idling and all that, when all of a sudden.....it started choking on me. At full throttle it wasn't even moving,...
  6. Yeah, just checked it today when I got home from...

    Yeah, just checked it today when I got home from work, everything seems fine. Tested a a few times and it's ok now. Just needed to dry that's all, just took a little longer than usual though. So...
  7. Just checked it again this morning before heading...

    Just checked it again this morning before heading to work only I didn't cross the wires yet. At first I got nothing, then all of a sudden it started to work again, then it would die on me again and...
  8. Throttle servo not working after taking a dip in a puddle.

    Ok, so I took the maxx 3.3 out to the park yesterday to finish off the rest of my fuel before winter hits, accidently ran it through a deep puddle in the grass. Then the truck decided to try to run...
  9. Replies
    3
    Views
    655

    Electric newbie

    I'm starting to get into electric, and I just purchased a brushed E-maxx (3903). Came with the 7-cell 3000 mah batteries. Took it out today at the park, came home disappointed...I swear it felt...
  10. Replies
    4
    Views
    226

    I just figured it out, all I did was increase the...

    I just figured it out, all I did was increase the tension on the throttle return spring on the linkage arm by pulling it a little and screwing it in place.
    A one minute job !
  11. Replies
    4
    Views
    226

    I disconnected all linkage from the throttle,...

    I disconnected all linkage from the throttle, then I tried it out by moving it with a screwdriver, same thing.
  12. Replies
    4
    Views
    226

    Stuck slider carb

    I noticed when I start the truck it was revving high. Realized the slider carb wasn't sliding all the way back to neutral, it would close maybe 3/4 the way, I have to push the slider shut.
  13. Replies
    5
    Views
    285

    HEY ! I did it ! Just took a little elbow...

    HEY ! I did it ! Just took a little elbow grease and as soon as I heard it "snap" together, I could swear I heard a round of applause.
    Thanks everyone for your help!
  14. Replies
    5
    Views
    285

    Center rear driveshaft repair problem

    Last week I damaged the differential yoke (4928x) on my maxxx 3.3 and lost the half shaft(5151) that was attached to it.
    So now I got the replacement parts, and I'm breaking my fingers trying to...
  15. Hey Andrea, Nice looking truck, especially the...

    Hey Andrea, Nice looking truck, especially the way you hid the antenna under the body..
    My family is also from Italy by the way..
  16. Replies
    11
    Views
    1,145

    You don't have to use Top fuel for break-in. ...

    You don't have to use Top fuel for break-in. Traxxas always recommends using it because it's their own company brand. But if you can get it at your LHS then go for it. But any nitro fuel will do,...
  17. Replies
    22
    Views
    1,414

    When I lived at home, my parents were cool with...

    When I lived at home, my parents were cool with it. Just as long as I don't rc on the grass (Dad used to tell me the exhaust fumes and oil dripping out the pipe leaves dead spots on his lawn).
  18. You might be running it too lean, go a little...

    You might be running it too lean, go a little more rich...it should help.
  19. Replies
    5
    Views
    256

    Stripped motor mount

    All the screws that connect the engine to the motor mount were loose on my tmaxx 3.3 I managed to tighten two of the four screws , the other two won't tighten, so I'm guessing the thread in the...
  20. Replies
    8
    Views
    307

    Make sure your motor mount screws are tightened,...

    Make sure your motor mount screws are tightened, all the vibration from the motor can cause them to loosen up over time and cause the engine to move, and when that happens, it's bye bye spur...
  21. Thread: Wheels?

    by nitroboy2
    Replies
    17
    Views
    487

    I checked out the site for them and it says 76...

    I checked out the site for them and it says 76 mounting screws are already included..
  22. Replies
    29
    Views
    514

    You can use ANY brand of 20% or 30% fuel on your...

    You can use ANY brand of 20% or 30% fuel on your Traxxas product. Whatever your LHS supplies is all good, I'm sure they know what they're selling.
    Traxxas recommends you to use their Top Fuel...
  23. Replies
    4
    Views
    291

    Since the part broke off underneath and past the...

    Since the part broke off underneath and past the slider carb, so i'm guessing that air was getting into the engine from where it cracked.
  24. Replies
    4
    Views
    291

    I broke my carburator

    I was out racing my Revo at the front of my house, when my buddy came out and started making a ramp out of an old sled he picked up on the curb (he works in waste disposal or garbage man, and proud...
  25. Replies
    6
    Views
    378

    try this :

    try this :
Results 1 to 25 of 129
Page 1 of 6 1 2 3 4