Search:

Type: Posts; User: xm_202_fan

Search: Search took 0.27 seconds.

  1. Replies
    10
    Views
    513

    The carb linkage bellcrank goes to far and...

    The carb linkage bellcrank goes to far and sticks.. i need to rotate the carb a little so this doesnt happen.

    I just hope its the clutch shoes.

    Thanks guys.
  2. Replies
    10
    Views
    513

    Ok. my throttle linkage bellcrank over rotated...

    Ok. my throttle linkage bellcrank over rotated and the truck was WOT upside down for about 30 seconds before I could shut it off. Now the truck wont move on the ground. If i lift it, the wheels go...
  3. Thread: screw size?

    by xm_202_fan
    Replies
    4
    Views
    141

    it is .5 ... For McMaster, use Item # 91294A130

    it is .5 ... For McMaster, use Item # 91294A130
  4. Thread: New Shocks

    by xm_202_fan
    Replies
    6
    Views
    248

    Better off going with Big Bores.. The...

    Better off going with Big Bores.. The Powerstrokes have been discontinued.
  5. Replies
    11
    Views
    505

    My LHS ordered 2 sets of the seal kits today for...

    My LHS ordered 2 sets of the seal kits today for me..
    Now I just hope thats all it is.... its a rear one so I dont feel like disecting until its repair time. The rears are a pain in the butt.
  6. Replies
    3
    Views
    285

    Yes... I destroyed my one way and chewed up my...

    Yes... I destroyed my one way and chewed up my starter shaft...... when I bought a new one way, I switched back to the ez start system... Im kinda scared to try the roto again.
  7. Replies
    11
    Views
    505

    Thanks for the suggestions guys.. I tried on...

    Thanks for the suggestions guys..

    I tried on ebay already... nothing.
  8. Replies
    11
    Views
    505

    Thats good to know.. But should I rebuild or...

    Thats good to know..

    But should I rebuild or just got to the BigBores?
  9. Replies
    11
    Views
    505

    Powerstrokes discontinued?

    I see on Tower that the Pro-Line Powerstrokes are discontinued.
    Bad timing.. One of mine is blown in the right rear.
    Should I rebuild the powerstrokes or just go with the big bores?
    I dont real do...
  10. Replies
    13
    Views
    399

    I got the RD Logics on the 2.5 and the shaftes...

    I got the RD Logics on the 2.5 and the shaftes keep popping out... Today I lost a rear.. repared it and 10 minutes later a front popped out.
    I do have a full set of MIP Shiny's on hand.. Imay be...
  11. Replies
    6
    Views
    347

    You may want to change both bulks while your at...

    You may want to change both bulks while your at it.. I had a very similar hard crash like that (them curbs do not move) and found that I had cracked my other bulk. I only spotted this after doing a...
  12. Replies
    1,142
    Views
    614,670

    Sticky: My 2.5...

    Details are in sig...

    http://i37.photobucket.com/albums/e94/ufdfireman/maxx-01.jpg
    *****
    http://i37.photobucket.com/albums/e94/ufdfireman/maxx-02.jpg
    *****...
  13. Replies
    16
    Views
    496

    What is a modded .18 TM??? ;) And what...

    What is a modded .18 TM??? ;)



    And what is the solution for this?

    Im getting my .18 TM tomorrow and I would like to be prepared.

    Also, is the manual's break in procedure good, or is...
  14. Replies
    15
    Views
    427

    Ballistic has a great package.. they do have a...

    Ballistic has a great package.. they do have a tray that you can charge the 8 TX batts in with the same charger.
    http://www.ballisticbatteries.com/Store_Detail.cfm?ID=2551&InfoID=200&ShowLarge=True...
  15. Im looking into this further, I had this idea...

    Im looking into this further, I had this idea myself - the search works great.
    I work in a machine shop so
    we have the materials and machines to do so. If we find a solution, we will make a nice...
  16. Thread: Stock Diffs

    by xm_202_fan
    Replies
    10
    Views
    308

    WOW I got lucky on that one. :p I just got...

    WOW I got lucky on that one. :p

    I just got done putting my Maxx back together after new bulks, all skids and chassis braces - all from ACNCM.

    I didnt think it made a difference - I got lucky...
  17. Replies
    19
    Views
    418

    I let my brother in law take my T-Maxx for a spin...

    I let my brother in law take my T-Maxx for a spin today (that was a mistake) -
    He slammed into a curb dead on squared at 3/4 throttle - here is the damage:

    broken bulkheads
    broken skidplate...
  18. Replies
    10
    Views
    483

    A couple other free file hosts are: ...

    A couple other free file hosts are:

    megaupload.com
    rapidshare.de
  19. Replies
    5
    Views
    248

    ok... ill let you know how I make out tomorrow. ...

    ok... ill let you know how I make out tomorrow.

    thanks for the help.
  20. Replies
    5
    Views
    248

    @ PhunkyPhish: The "good luck" scares me. ;)

    @ PhunkyPhish: The "good luck" scares me. ;)
  21. Replies
    5
    Views
    248

    Changing chassis

    I was wondering what the best procedure is for changing chassis. I got the lightweight chassis from Fastlane.
    The truck is brand new and never been taken apart so I am not familiar with the...
Results 1 to 21 of 22