Search:

Type: Posts; User: madscrapper85

Page 1 of 17 1 2 3 4

Search: Search took 0.17 seconds.

  1. Replies
    8
    Views
    724

    Interested in the rustler roller pm me a price

    Interested in the rustler roller pm me a price
  2. Replies
    3
    Views
    362

    Bump it up

    Bump it up
  3. Replies
    3
    Views
    362

    Can't build one this clean with these parts for...

    Can't build one this clean with these parts for this cheap guys. She needs a new home somebody to use her
  4. Replies
    3
    Views
    362

    Found an tq rx/TX couldn't build this truck that...

    Found an tq rx/TX couldn't build this truck that cheap let's get somebody a great truck
  5. Replies
    3
    Views
    362

    f/s my baby P4de

    Selling my built p4de here's the build thread http://traxxas.com/forums/showthread.php?9007902-finally-building-my-p4de.

    Everything that can be upgraded has been. Will need a rx/tx and batts. I...
  6. Yea drill bits and a dremel tool lol every...

    Yea drill bits and a dremel tool lol every little bit helps.

    Also weight doesn't affect top speed just acceleration so worry more about gearing and battery's unless you have a small space to run...
  7. Replies
    17
    Views
    249

    If you want it right go aluminum in the blocks...

    If you want it right go aluminum in the blocks the steering ing and the holders. Yes you can replace them six times with stock but what about the seventh. And they will break over and over go...
  8. Replies
    13
    Views
    446

    They definitely make a huge difference in the...

    They definitely make a huge difference in the handling even if you don't run it like a race truck.
  9. Replies
    6
    Views
    195

    Is it just me or are the teeth on that pinion...

    Is it just me or are the teeth on that pinion damage as well could just be the pic. I would replace both the ring and pinion if either was worn.
  10. With the suspension at full drup my diffs seems...

    With the suspension at full drup my diffs seems to bind but as long as there is some load on it its seems to spin free. You could run it for a few minutes and just temp it every 2 minutes or so...
  11. Replies
    527
    Views
    24,414

    If your not running a bec with that servo then...

    If your not running a bec with that servo then your not getting full potential out of it and at 7.4v its as fast as the traxxas with 50 more oz of torque
  12. thats a new one for me man sorry never heard...

    thats a new one for me man sorry never heard clinking like that. If you take the axles loose and spin the pinion with the driveshaft is the noise still present.
  13. Replies
    700
    Views
    17,667

    Only concern I see with the way you have cut the...

    Only concern I see with the way you have cut the hole the edges are too straight a corner will crack not matter how re enforce it. They need to be rounded in the corner then you should be ok. it...
  14. What axles are you running up front

    What axles are you running up front
  15. Replies
    700
    Views
    17,667

    Did you make an exit in the rear or are you just...

    Did you make an exit in the rear or are you just letting it flow out the bottom
  16. Make sure you re enforce the rear of the body...

    Make sure you re enforce the rear of the body over the shock towers my son had the same one two days after I painted it and shoe gooed and taped it the entire rear section of the body snapped off...
  17. Replies
    5
    Views
    129

    Most likely a diff but before you dive in the...

    Most likely a diff but before you dive in the make sure you check the basics, wheel hexes, drive shafts set screws, slipper tight. If that's all good open the diffs and enjoy upgrading to xo1 spec
  18. Replies
    47
    Views
    1,269

    The mmp is great if you don't go near water may...

    The mmp is great if you don't go near water may want to look at a1/8 sidewinder esc if you ever want to play in the mud or wet condition. Lots of guys love the hobbywing sc8 wp. I can't attest to...
  19. What kinda track is the club building, if it's a...

    What kinda track is the club building, if it's a flat track you need to lower the suspension possibly and easiest way would be to put some air line tubing underneath the piston inside the shock body....
  20. Get an aluminium bearing adapter and a fan for...

    Get an aluminium bearing adapter and a fan for your esc and motor then replace what breaks
  21. You forgot the part about being pulled thru the...

    You forgot the part about being pulled thru the turns and mid air controllability is far better, but you can't stick the brakes and slide the rear end around 180 degree turns like you can a 2wd. If...
  22. Replies
    10
    Views
    303

    I run both the diff makes a huge difference on...

    I run both the diff makes a huge difference on handling but if yo are bashing it does create a weak spot. I've run it on 4s with a mmp/2400 combo and it has never let me down but I have a spare...
  23. I know it's still just 3s with no programming...

    I know it's still just 3s with no programming interface other than the transmitter, they did put the caps on it so hopefully the bec is better. Don't see it being much more than 90a.
  24. +1 your right you really can't beat that deal its...

    +1 your right you really can't beat that deal its a great set up
  25. Replies
    11
    Views
    313

    Be carefull of the 4600 in the 4x4 its a great...

    Be carefull of the 4600 in the 4x4 its a great 2wd motor but it doesn't have what you need for a 4x4 it gets too hot to fast. See if you can find a 3800 much better for what your doing. If you can't...
Results 1 to 25 of 407
Page 1 of 17 1 2 3 4