Search:

Type: Posts; User: new2slash

Page 1 of 3 1 2 3

Search: Search took 0.11 seconds.

  1. Replies
    5
    Views
    318

    Hmmm to bad. Well i have to go strip 1 car and...

    Hmmm to bad. Well i have to go strip 1 car and put it's receiver in the slash and use the transmitter for that one, now for the slash.
    My old tamiya tl-01 will then get the '25 yards' ttraxxas...
  2. Replies
    5
    Views
    318

    Lets say i have fm now. The electrics 'behind...

    Lets say i have fm now.

    The electrics 'behind the crystals' are for fm OR am only?

    Just for beeing sure, i did not ment:
    fm in trasmitter and am in receiver! (I know both must have same band...
  3. Replies
    5
    Views
    318

    other freq. on tq and receiver

    Hi, i know little about transmitter/receivers.

    If i have a pair of crystals for receiver and transmitter (they do physically fit) but they are AM instead of fm
    (or fm instead of am, anyway...
  4. Replies
    44
    Views
    1,012

    I hope it is finaly a BL truck, 4wd, cardan, not...

    I hope it is finaly a BL truck, 4wd, cardan, not belts.
    Pricewise, if they make/order enough esc's, alu.shocks etc. it is cheaper for them to make.

    They even may want to get in to this market and...
  5. Ok you 2 thanx for the swift replyes!

    Ok you 2 thanx for the swift replyes!
  6. newbee Q on receiver and lipo+BL in slash

    If i have my lipo set (charger, 2s lipo 5000 mah, lvc) i suddenly ask myself, and you all here now, what about the receiver?

    I have a brushless esc and motor, lrp x11, and drive it with a 4000...
  7. Replies
    5
    Views
    252

    Okay all, it is finally clear to me, thanks for...

    Okay all, it is finally clear to me, thanks for all the replys!!

    My esc does not have lvc, so i need such a in-between esc and receiver cut off.
  8. Replies
    5
    Views
    252

    newbee lipo cut off question

    I have decided, i will go LIPO on my slash.
    Lipo charger, 220v with built in balancer and 2 cells lipo's (not 3)

    But i keep reading on voltage protection. IN car i mean.

    So how is that done?...
  9. traxxas webshop, flatrate, replace items

    First hit i had with the slash after 20 runs or so was BINGO, broken of a caster block, the steel pole was harder then the slash's front part.

    So i went looking for replacement, only -1- shop (i...
  10. Replies
    14
    Views
    442

    Site vs real measurement by garmin nuvi 660t GPS...

    Site vs real measurement by garmin nuvi 660t GPS

    http://i249.photobucket.com/albums/gg207/usegrouper/slash6cnimh72-471kmu.jpgright column, 47.1 km p/h

    So the site is pretty accurate i.m.o.
    my...
  11. Replies
    27
    Views
    1,701

    Anyway, let's all GPS our cars and name the...

    Anyway, let's all GPS our cars and name the setup! :-)
    I use a LRP x11 7.5t BL sensored (9 wires) and with a simple 6 cell nimh pack i hit 47.1 in less then 20 meters with 17t pinion and 90t spur....
  12. Site vs real measurement by garmin nuvi 660t GPS...

    Site vs real measurement by garmin nuvi 660t GPS

    http://i249.photobucket.com/albums/gg207/usegrouper/gps-slash-17-90-bl-6000kv.jpg

    right column, 47.1 km p/h...
  13. You all did fill in the total motor rpm's (i.e....

    You all did fill in the total motor rpm's (i.e. 7,2 x 6500 = 46800) , tire diameter (2.2 inch or more/less) , 6 cell (or more) lipo OR nimh, etc.?
  14. Replies
    14
    Views
    442

    Found a great site for this !! ...

    Found a great site for this !!
    ...
  15. Predictable speed site ! rpm's, ratio etc.

    This is 1 great site i found !!
    It measures given knowns in to theoretical speeds !!

    my calculated setup & speed
  16. Replies
    14
    Views
    442

    so with the standard 12t (24.000 rpm?) , the...

    so with the standard 12t (24.000 rpm?) , the wheels make 8824 rpm
    with 2.2 inch wheels that is 6,9 inch per rotation
    6,9 times 8824 = 60806 inches per minute
    x 60 = 3648360 inches per hour...
    ...
  17. Replies
    14
    Views
    442

    On http://wahiduddin.net/calc/calc_speed_rpm.htm...

    On http://wahiduddin.net/calc/calc_speed_rpm.htm
    What should one fill in there for the slash, at:

    Transmission Gear Ratio ??
    Differential Gear Ratio ??
  18. Replies
    14
    Views
    442

    1 mile = 1609,344 meter 1 kilometer = 0,621371...

    1 mile = 1609,344 meter
    1 kilometer = 0,621371 mile
    http://nl.wikibooks.org/wiki/Omrekenen_van_eenheden/Lengte
  19. Replies
    10
    Views
    1,560

    Bit weird to me, because 16 and 90 is less...

    Bit weird to me, because 16 and 90 is less resistance then 18 and 86..
    I have the 7,5t on 17 / 90 and is i guess about 45 celsius.
    What brand of brushless motor are yours and friends?


    Same...
  20. Replies
    14
    Views
    442

    Where does this come from: mph = .00297432 ??...

    Where does this come from: mph = .00297432 ??
    Aint this simpler, i.e. my slash ? :

    Primary: (spur / pinion) 90 / 17 = 5.294
    Internal: (diff / center) = 2.72
    FINAL DRIVE RATIO 5.294 x 2.72 =...
  21. Replies
    10
    Views
    1,560

    Hi dutch, another dutch here :-) I use a LRP 7,5...

    Hi dutch, another dutch here :-)
    I use a LRP 7,5 t with 9 wires (programmable, reacts like a brushed motor)
    With low windings and high rpm, the topspeed is great, and still spinning starts, great...
  22. Replies
    10
    Views
    424

    Should that cahrger work on 110 / 220 v ...

    Should that cahrger work on 110 / 220 v wallsockets WITHOUT ground wire (so 2 wires only) ??
  23. Replies
    10
    Views
    618

    The better the mesh the quieter it is. Also an...

    The better the mesh the quieter it is.
    Also an aftermarket aluminium 17 t 'silencer pinion' was notacibly quieter.
    The the grease/oil used on gears will do some silencing i gues.
    The more space...
  24. Replies
    15
    Views
    809

    From my opening post: I top it of with a peace...

    From my opening post:
    I top it of with a peace tape.
    And i forgot (due to taking to much time for dis- and assemblage) to grease the gears, did not want to do that all over again just after...
  25. I.m.o. you should not have... Doing free work...

    I.m.o. you should not have...
    Doing free work for the lazy manufacturer...
Results 1 to 25 of 64
Page 1 of 3 1 2 3