Search:

zreuille, Thanks for the link

Brett the grass isn't very tall but it does come up to the chassis and was just looking at getting a little more lift so it doesn't bog down. to answer your...

I have a parking lot to run it in at home but when I go off road it is on grass and I want to know if there is a way to get a little more ground clearance. I have thought about putting larger tires...

I have that same combo on my rustler and the gearing I use is 19/90. The chart that comes with it will reccomend the largest spur available and a 19 pinion max I had a 23 pinion on there for a while...

not trying to hijack the thread but was wondering if it is safe when using them for storage is it safe to store more that one battery in a bag?

One other thing I would suggest is with the XL-5 make sure to read the manual on how to "Break In" the titan motor it will make it last alot longer.

from what I have heard that will work just as good as with the station but I don't know from experience. For the rear you would need to find a way to disconnect the axle from the driveshaft but I...

I would like to make a suggestion to not call the people trying to help stupid as that may lead to no one wanting to help.

That being said there is a section in the manual that says to try...

First welcome to the forum and to the hobby. There isn't much more to be said. as most have said don't worry about upgrading a part until you break something and you get used to driving it, when a...

you should be able to balance them while on the vehicle, prop the tires up off the ground and the front wheels will spin free enough to be balanced.

Here is one of many videos on how to balance tire
http://www.youtube.com/watch?v=eo8uq_WkcXA

online version of the manual
http://traxxas.com/sites/default/files/24054-36054-37054-OM-N-EN-R00_6.pdf

Speed Control is somewhere around page 18 i believe.

If it is an older rustler it is probably an older AM receiver. This was happening to me and I found I had accidently routed the antenna wire next to the power wire and I think it was causing...

Not sure where you are getting that from but I had an XL-5 and don't remember seeing anywhere in the manual that it can run a velineon motor. If for no other reason brushless motors use three wires...

I agree with KSB51rl I say go by the manufacturer of the BATTERY. The ones that are with the charger are a general estimate.

The battery manufacturer will have specific. I have 3000MAH that can...

if it is still under warranty I would contact traxxas they will most likely replace it. If you try to fix it you could damage it even worse and that would not be replaced.

as far as the charger I would contact the manufacturer any advice on non traxxas equipment may get the thread closed.

The benefit of going with an 7 cell (8.4v) would be that you are getting more...

You can find a bunch of videos on you tube, but here is the Traxxas method
http://traxxas.com/support/Brief-break-period-required-Titan-12T-motor

I just took another look and it looks like that is a midnight motor is that correct?

If that is the case, I have the same motor , for about 20 -25 dollars at the local hobby store you cn get a...

I agree with O.G. no matter what get rid of the tamiya connectors with the increased draw through them they will heat up, the plastic will start to soften and that will cause the connection to...

Can't be sure without seeing it but the spark could have been the normal arc you get when you connect two wires under a load, it could also have been a sign of something shorting out which may have...

then like harry 697 said I would see if you have the screws next to the post if you do then it would be easier to just get a new set of brushes and screw them on using the eyelet. If you solder it...

I would also recommend going brushless, I had a titan for about 7 months and had no problems, however I have heard of people on here having problems with them burning out, and there are plenty of...

I had rear rims mounted on the front at one point and on mine the nut would bottom out on the pin before tightening on the rim and it wobble and the pin the goes through would fall out after a while,...

the hose is probably the problem.

do you re oil the bushings afterward??

every 3-4 runs you should remove the motor from the truck use electric motor cleaner to flush it out then let it dry...

If you were running Nimh and switched too lipo you could be sending more power through the motor at one time, that would require you too gear down a little bit it could be making the motor heat up...