Search:

Type: Posts; User: WorkingDad

Page 1 of 11 1 2 3 4

Search: Search took 0.42 seconds.

  1. Replies
    6
    Views
    195

    Ah, thanks. Didn't realize they could be gotten...

    Ah, thanks. Didn't realize they could be gotten separately. Was kind of hoping RPM had gotten into the game too though.
  2. Replies
    6
    Views
    195

    That is a nice project Jezza. A 4x4 conversion...

    That is a nice project Jezza. A 4x4 conversion may be in my future. Wonder what I'd have to get to go down that route...

    I've gotten a couple buddies into the hobby now too, and we've been...
  3. Replies
    6
    Views
    195

    Extended A Arms

    It's been a while since I've been in here. I built up my Stampede last year, pretty much ended up with a completely new one from scratch after all was said and done. The leftovers became a pretty...
  4. Thread: Hinge pins?

    by WorkingDad
    Replies
    18
    Views
    287

    I haven't broken out my Stampede for a few...

    I haven't broken out my Stampede for a few months. Took it out last weekend and ran it through it's paces. Decided to strip it down fully for a good cleaning. I couldn't get the front left STRC...
  5. Replies
    71
    Views
    2,663

    That is really nice looking.

    That is really nice looking.
  6. Check Pepboys too, especially local ads. Some of...

    Check Pepboys too, especially local ads. Some of their stores sell Stampedes. My local one had a couple for 20% off on a table up front not too long ago. Coupons would work there.
  7. Replies
    67
    Views
    2,889

    FWIW, I started using the 3685 washers on the...

    FWIW, I started using the 3685 washers on the rear axles: http://www3.towerhobbies.com/cgi-bin/wti0001p?&I=LXJK64 . It's the part listed in the VXL exploded diagram. I haven't had an issue with...
  8. Replies
    92
    Views
    3,589

    That is some hot stuff. I've been wondering if a...

    That is some hot stuff. I've been wondering if a Lightning McQueen body could be made. I've seen some homespun ones that were... close, but I'm looking for something top notch. My son would flip.
  9. Replies
    79
    Views
    2,734

    If the pinion is turning the spur and the wheels...

    If the pinion is turning the spur and the wheels are not moving, it's likely something inside the transmission.

    Take the spur and slipper off, make sure there is a small pin through the shaft...
  10. Replies
    8
    Views
    180

    Probably a good excuse to replace the bushings...

    Probably a good excuse to replace the bushings with bearings then. avidrc.com is a good source for them, or Traxxas has them as well.
  11. So let's get down to brass tacks here Ramsey,...

    So let's get down to brass tacks here Ramsey, where are you going to start manufacturing and selling these? ;)
  12. Replies
    26
    Views
    504

    Heck, just wrap them in a few layers of duct tape...

    Heck, just wrap them in a few layers of duct tape :)
  13. Replies
    26
    Views
    504

    I feel the same way.

    I feel the same way.
  14. Replies
    4
    Views
    91

    The Traxxas caster blocks should come with the...

    The Traxxas caster blocks should come with the pins. They'll screw in from the bottom. If you go with bearings, it's certainly not going to hurt to upgrade the carriers as well. I put aluminum...
  15. Thread: Hi all.

    by WorkingDad
    Replies
    31
    Views
    430

    I like them, I get a lot of my parts from them....

    I like them, I get a lot of my parts from them. Did you break the stock caster blocks or aluminum?
  16. Replies
    16
    Views
    375

    How about I buy it from you for $60? You'll make...

    How about I buy it from you for $60? You'll make $10 ;)
  17. Guy at the LHS said I might be keeping on the gas...

    Guy at the LHS said I might be keeping on the gas when landing a jump. Honestly, the times it's broken have been when my nephew has been driving and I haven't paid attention to how he does the...
  18. You rock! Thanks. Adding those to my upgrade...

    You rock! Thanks. Adding those to my upgrade list.
  19. What parts do you need to convert over to the AE...

    What parts do you need to convert over to the AE slipper? Do you happen to have any links? I've been Googling around, but not quite sure what to look for so my searches are coming up bust.
  20. Replies
    7
    Views
    160

    I wouldn't worry about the steel shafts. I'm...

    I wouldn't worry about the steel shafts. I'm using the 4x4 shafts (plastic) and they're fine. I ran with the stock shafts for a while too with no problem, just moved them over to the kids' truck...
  21. Yep, that's how mine works. Those things won't...

    Yep, that's how mine works. Those things won't come out of the slot either, once they're in. It's a good solid connection to the chassis though.
  22. The FLM case is great. Put a few dings and...

    The FLM case is great. Put a few dings and scratches in it this week, with this pin doing its work and some general bashing. I was able to take it apart, replace that shaft and get it back together...
  23. I need to check that out. That's the one that...

    I need to check that out. That's the one that requires a different clutch, if it's not too much of a change I may go that route.
  24. I'll try the allen wrench. I thought the nail...

    I'll try the allen wrench. I thought the nail would've been pretty string. It looks like it slipped out just a tad, then got caught on the housing and bent. Did some minor damage to the inside of the...
  25. I keep breaking the pin in the top shaft...

    I don't know what I'm doing, but I'm on my 3rd top shaft pin in 2 months. It's the one that sits behind the gear on the input shaft of the transmission. I replaced it with a piece if a nail at first,...
Results 1 to 25 of 265
Page 1 of 11 1 2 3 4