Search:

Type: Posts; User: JDGecko

Page 1 of 4 1 2 3 4

Search: Search took 0.18 seconds.

  1. Replies
    24
    Views
    1,254

    Jinx... Better know on some wood.

    Jinx... Better know on some wood.
  2. Replies
    24
    Views
    1,254

    This one put me out of commission for quite a...

    This one put me out of commission for quite a while. MMP 2400 on 3s full speed into a car tire. Front A-arm, front shock tower, bent center drive shaft, folded over chassis, bent front Tekno half...
  3. Replies
    26
    Views
    3,039

    PM sent. Thanks crusey!

    PM sent. Thanks crusey!
  4. Replies
    26
    Views
    3,039

    Hey Crusey, Can you share you you...

    Hey Crusey,

    Can you share you you accomplished this? I have a DX3s and bought it for the sole purpose of turning my lights on and off. All my research turned up was cumbersome solutions similar...
  5. Yep... I have seen pinions like that over and...

    Yep... I have seen pinions like that over and over on my Slasher. I too put the RR spur in mine with stock pinions and they all came out looking like that after some heavy bashing. So.. I tried the...
  6. Replies
    2
    Views
    274

    Yes, the black bars are stiffer.

    Yes, the black bars are stiffer.
  7. I love that site... LOL

    I love that site... LOL
  8. Thread: Slash topless

    by JDGecko
    Replies
    28
    Views
    1,774

    I pitched my overtray. It made my chassis...

    I pitched my overtray. It made my chassis compartment an absolute oven! I understand that it's partially my fault as I didn't cut any ventilation holes in it but if I did, it wouldn't keep stuff...
  9. Thread: Parts

    by JDGecko
    Replies
    5
    Views
    219

    Most...! My list includes Drive shafts both...

    Most...!
    My list includes Drive shafts both stock and Tekno (replaced with MIP's)
    A-arms (replaced with RPM)
    Shock towers (replaced with RMP)
    Slipper clutch (replaced with Robinson Racing)...
  10. Thread: Slash topless

    by JDGecko
    Replies
    28
    Views
    1,774

    Get an Outerwears "prefilter". Covers the entire...

    Get an Outerwears "prefilter". Covers the entire chassis from all debris and moisture (water/snow) while still allowing air flow. My friend and I did this and haven't looked...
  11. Replies
    5
    Views
    699

    Do the HiTec and Savox have the same tooth mesh...

    Do the HiTec and Savox have the same tooth mesh for the servo horn? I broke my stock server so I installed a Spektrum servo. The teeth didn't quite match up so I stripped my servo horn. Had to by...
  12. I agree... 16t is nice and peppy. 18t is a...

    I agree... 16t is nice and peppy. 18t is a little bit crazy, fast and fun. Then, I ran 20t last night.

    On 20/54 I had some pretty crazy crashes with my truck and am shocked I didn't break more...
  13. You guys are correct, my bad.... I ordered one...

    You guys are correct, my bad.... I ordered one along with my mount thus the confusion.
  14. I believe the KingHeadz motor mount comes with a...

    I believe the KingHeadz motor mount comes with a new metal bearing adapter. Mine did anyway...
  15. If this is true it will save me a lot of...

    If this is true it will save me a lot of $$$$'s... Lexan paint is expensive and I can only do one body with it.
  16. Replies
    19
    Views
    1,004

    I am going to use Blue because frankly, Red...

    I am going to use Blue because frankly, Red scares me a bit. Paranoid I won't be able to get them foo without a blow torch.

    Ironically, I received my front MIP's today at work and the...
  17. Replies
    16
    Views
    1,261

    My buddy has MIP's all around and I am switching...

    My buddy has MIP's all around and I am switching from Tekno's to MIP's on the front. My front Tekno's pop out on wheelies.
  18. My Tekno front drive shafts pop out and I think I know why...

    So we were basking around yesterday with our new MMP SCT 2400's yesterday on 4s. So much fun by the way. After a while I was experiencing the front drive shafts of my Tekno's kept popping out of...
  19. Replies
    19
    Views
    1,555

    Definitely check if it's in LiPo mode. The ESC...

    Definitely check if it's in LiPo mode. The ESC that came with my truck was set up in Nimh mode. I have since replaced the esc twice (varying reasons) and both replacements have come back in LiPo...
  20. A-Main - little higher in prices but greeeeat...

    A-Main - little higher in prices but greeeeat shipping
    RC Boca - Best prices but so so shipping

    My only 2 sources online
  21. Replies
    9
    Views
    391

    Add me to the list... Fortunately I had a spare...

    Add me to the list... Fortunately I had a spare in my kit so I was up and running again quite quickly.
  22. Replies
    15
    Views
    1,002

    The upgraded parts included with the Ultimate are...

    The upgraded parts included with the Ultimate are definitely worth the ~$100 increase. Add sway bars ($25) to the list of parts listed above. Aluminum parts would run about $100 retail and the...
  23. Replies
    21
    Views
    695

    Where do folks get the mount that holds the...

    Where do folks get the mount that holds the switch for the ESC? I am in the process of installing my MMP 2400 and would like to get one of those before i get to far.
  24. I know others have used alternate materials and...

    I know others have used alternate materials and I'm sure they will chime in. Me? I love my outerwears. Is it expensive, overpriced and feels like a rip off? yes... But it fits and works perfect...
  25. Just sent my ESC and motor in yesterday... Both...

    Just sent my ESC and motor in yesterday... Both just suddenly stopped working. Swear it had something to do with the solar storm!!! :((

    Oh and yes, they do take care of ya!!!!
Results 1 to 25 of 93
Page 1 of 4 1 2 3 4