Search:

Type: Posts; User: jackislost

Page 1 of 8 1 2 3 4

Search: Search took 0.21 seconds.

  1. Replies
    2
    Views
    103

    The rally drive shafts are shorter than the...

    The rally drive shafts are shorter than the Tetons drive shafts, I have both. The Tetons arms are longer than the rally's. Everything on the chassis is interchangeable. I tried the rally with Teton...
  2. Replies
    3
    Views
    172

    I am not sure, I think it is 3racing assosicated...

    I am not sure, I think it is 3racing assosicated 18r wheel and tires. RJ from "the toyz" sold them to me opened package. They came with adapters to make the 18r into hex drives but the latrax was...
  3. Replies
    3
    Views
    172

    ridemakerz body is a good fit!

    I bought this body from ridemakerz near Disneyland. I really like this body, it is kind of heavy but it has LEDs. I use super strength magnets on the shock towers and inside the body, works great and...
  4. Replies
    1
    Views
    82

    shock towers

    Anybody else notice the rear shock towers make the car a good ride height and the front shock towers make the car angle downwards? I ordered another shock tower set to run both rear shock towers in...
  5. Replies
    25
    Views
    629

    toro is half the price, for starters :)

    toro is half the price, for starters :)
  6. Replies
    25
    Views
    629

    I don't have that motor set-up but I do have the...

    I don't have that motor set-up but I do have the mamba. Both are made in China (I know the mamba 0808 is, mine says so on the can) but the mamba seems smaller and lighter, for more serious racing....
  7. Replies
    25
    Views
    629

    If I had to do it again I wouldn't buy my mamba...

    If I had to do it again I wouldn't buy my mamba and I would have bought this combo
  8. Replies
    4
    Views
    127

    There's a thread on it on the Teton forum.

    There's a thread on it on the Teton forum.
  9. Replies
    4
    Views
    127

    Just dremel the stock motor mount a little. I...

    Just dremel the stock motor mount a little. I would get bearings and the diff gears from a Teton
  10. Replies
    6
    Views
    165

    The shocks on the Teton is a lot longer, it will...

    The shocks on the Teton is a lot longer, it will not fit the short sock posts from the rally. I think you will need the teton's shock posts. I have the Teton parts but I never tried it.
  11. Replies
    17
    Views
    725

    i really like your scheme on that buggy

    i really like your scheme on that buggy
  12. Replies
    6
    Views
    165

    if you spend around $35 for a brushless system,...

    if you spend around $35 for a brushless system, you can get a wide arrangement of brushless motors. I had good experience with Tacon motors in the 2040 size. they are a bit big because they come with...
  13. Replies
    6
    Views
    165

    Try checking the drive shaft on the right sides...

    Try checking the drive shaft on the right sides or the diff out drives. For a bulletproof drive train I suggest you get the Latrax Teton diff gear rings and a set of bearings. I would also get a...
  14. Replies
    3
    Views
    187

    This one is not meant to be driven on dirt or...

    This one is not meant to be driven on dirt or anything. It is an on road car with a rally body. I can hardly make it over extension cords without getting stuck. Other than having no off road...
  15. Replies
    2
    Views
    202

    I changed all the oil to 45, wish I had 60-65ish

    I changed all the oil to 45, wish I had 60-65ish
  16. Replies
    5
    Views
    218

    My rally and Teton both have toe in, it's a...

    My rally and Teton both have toe in, it's a little annoying. I wish there were adjustable rods
  17. Replies
    10
    Views
    319

    It would be hard to mod the chassis because the...

    It would be hard to mod the chassis because the center shaft will be under the chassis if you raise the chassis clearance.
  18. Replies
    4
    Views
    117

    You can try to trim the radio to center. Power...

    You can try to trim the radio to center. Power everything on, then let the servo center, then take the servo horn off and align it 90 degrees straight up. Adjust the push/pull rod as needed....
  19. Replies
    4
    Views
    117

    The rally doesn't come with bearings and I think...

    The rally doesn't come with bearings and I think one side of your drive train is causing more friction than the other side, slowing one side down. That's my guess. Hold one wheel and press the gas...
  20. Replies
    15
    Views
    2,316

    Sticky: http://i12.photobucket.com/albums/a227/Jack_Nguyen...

    http://i12.photobucket.com/albums/a227/Jack_Nguyen/Mobile%20Uploads/IMG_20140613_205404_zpsdz80yeqv.jpg...
  21. Replies
    2
    Views
    275

    New body, comes with 2 LEDs in headlights, 4x in...

    New body, comes with 2 LEDs in headlights, 4x in rear lights, and one long one under the hood scoop. The wheels are slightly small for the body so I'm looking for slightly bigger wheels. I like this...
  22. Replies
    24
    Views
    677

    I wouldn't try bending the center out, might bend...

    I wouldn't try bending the center out, might bend the whole ring. Dremel seems safer and more precise.
  23. Replies
    24
    Views
    677

    Do you have a dremmel?

    Do you have a dremmel?
  24. Replies
    2
    Views
    275

    started as a Teton, ends as a rally

    I've been waiting for the rally drive shafts for a while now, tomorrow I will finally run this beast.
    My electronics are: spektrum SR3300T, Mamba Micro Pro 0808 4100kv, Savox SH-0257mg, Onix 3s...
  25. I was talking about the metal ring gear on the...

    I was talking about the metal ring gear on the spool. I think I'm going to go back to two gear diffs
Results 1 to 25 of 189
Page 1 of 8 1 2 3 4