Search:

Type: Posts; User: scha0786

Page 1 of 2 1 2

Search: Search took 0.11 seconds.

  1. 10-4 I will order that kit up, thanks!

    10-4 I will order that kit up, thanks!
  2. but why in the review someone mentions that it is...

    but why in the review someone mentions that it is not the correct kit, that its for the old style motor? The new motor apparently uses 11x5x4 instead of 11x5x5 bearings.

    thanks for the help just...
  3. velineon brushless 3500 rebuild kit, where to order?

    I want to rebuild my 2 yr old brushless slash 2wd motor, just as preventative maintenance. I have done some limited research and I have the newer version 3500 motor. Only the one side of the motor...
  4. Spektrum DX3s with SR3300T throttle glitch, help

    bought a new spektrum DX3s with SR3300T receiver from Amain couple months ago. Hooked everything up and now my throttle totally cuts out. Things I've tried:

    Rebinding
    resetting throttle limits...
  5. Replies
    16
    Views
    745

    19/90 is a good set up I have tried 23/86...

    19/90 is a good set up I have tried 23/86 (stock), 19/86, 23/90 and the 19/90 is my fav
  6. they look sweet, gonna order up 8 of the...

    they look sweet, gonna order up 8 of the revolution.
  7. yep got the teflon shim. I am not the only one...

    yep got the teflon shim. I am not the only one wearing out bearings. 2 other trucks have been doing the same. Track has a heavy right banked turn. Basically you can pin it into the corner and turn...
  8. wheel bearings keep wearing out, alternative?

    So I have a 2wd brushless slash with Proline calibers around. I am typically running 2s lipo's with the occasional 3s. The track I run is hard clay with a lot of small bumps and some big jumps.

    My...
  9. Replies
    11
    Views
    731

    hmm....well I already ordered all the stuff. I...

    hmm....well I already ordered all the stuff. I will keep an eye on those c blocks and upgrade to aluminum if needed. I like to do things the hard way
  10. Replies
    11
    Views
    731

    I just ordered rpm axle carriers front and rear,...

    I just ordered rpm axle carriers front and rear, rpm caster blocks, traxxas 5x11x4 bearings and lungsford titanium axle hing pin kit. I went with lungsford because some of the reviews stated that the...
  11. Thread: Upgrades?

    by scha0786
    Replies
    11
    Views
    590

    do the big bores use larger diameter shock...

    do the big bores use larger diameter shock shafts? or do they just use the titanium shafts same diameter? i am thinking about the rpm 2 stage piston setup
  12. Replies
    11
    Views
    731

    yeah rpm is my choice

    yeah rpm is my choice
  13. Replies
    11
    Views
    731

    I read a review on the ST aluminum caster blocks...

    I read a review on the ST aluminum caster blocks and seems that the lower hinge hole is too small.

    Would the traxxas be a better option?

    what is the advantage of the 30 degree ones?
  14. Replies
    11
    Views
    731

    correction, A-arm hing pins ok I see that ST...

    correction, A-arm hing pins

    ok I see that ST racing has some hardened polished threaded kit for 15.49, I'll give those a try.

    Yeah I will go with the RPM axle carriers and order new larger...
  15. Replies
    11
    Views
    731

    Axle pins and axle carriers

    hello,

    I am tired of my rear inner axle pins threading out, all though a little WD-40 seemed to help lately.

    I was wondering what is a better option:

    Lungsford titanium hinge pin kit with...
  16. Replies
    10
    Views
    394

    SPC batteries are top notch!! I have two of the...

    SPC batteries are top notch!! I have two of the 2s 5000mah and one 3s. I can get around 45mins runtime on the 2s packs each! The 3s I have only run here and there because the truck is crazy fast on it
  17. Replies
    18
    Views
    1,345

    my traxxas fan seems to have a bad bearing or...

    my traxxas fan seems to have a bad bearing or something. It makes a bunch of noise on start-up, like the bearings are shot and then finds a sweet spot and quiets down and moves air. Gonna take it...
  18. nevermind, found it on a main hobbies for like...

    nevermind, found it on a main hobbies for like 9.25
  19. I made this change at the same time I installed...

    I made this change at the same time I installed the pro-line suspension kit too. Is there an alignment tool I can buy? I did it using a square.
  20. could having my front tires slightly toe'd out be...

    could having my front tires slightly toe'd out be the problem too?
  21. ok, ill try the stock vxl 2075 servo when i get...

    ok, ill try the stock vxl 2075 servo when i get home again, thanks!
  22. Thread: Upgrades?

    by scha0786
    Replies
    11
    Views
    590

    i went with the upgraded nitride shock shafts and...

    i went with the upgraded nitride shock shafts and have good luck so far. the big bores are not really worth the money.

    motor heat sink and gear lower if running lipos, helps keep the heat down.
    ...
  23. yeah its the proline, full ball bearing kit. i...

    yeah its the proline, full ball bearing kit.

    i will give that swing on stand and check for binding. i did that when i installed the kit. i am thinking it is the servo.

    my stock 2075 did the...
  24. steering problem, constant adj steering trim

    I've got a weird problem with my steering. when driving it in any condition/track I constantly have to keep adjusting my steering trim from left to right. It seems that this started after I installed...
  25. Replies
    25
    Views
    895

    2s is plenty for racing! Pulls wheelies! Haven't...

    2s is plenty for racing! Pulls wheelies! Haven't even put in the 3s yet, lol. Run time is awesome and charge time for the 2s is around 65 minutes.

    I really like the Duratrax charger, once it is...
Results 1 to 25 of 36
Page 1 of 2 1 2