Search:

Type: Posts; User: maxxdrevo

Page 1 of 3 1 2 3

Search: Search took 0.07 seconds.

  1. Thread: tire glue??

    by maxxdrevo
    Replies
    8
    Views
    1,111

    Fusion by AKA is some great stuff.. It works 100...

    Fusion by AKA is some great stuff.. It works 100 times better than the Pro Line... Oh and dont get any on ya.... You will have a mark for 3 or 4 days....
  2. Thread: 3.3 Failure

    by maxxdrevo
    Replies
    36
    Views
    1,994

    The pitting I see isnt typical to detonation. ...

    The pitting I see isnt typical to detonation. The pitting I see is from debris such as a piston skirt or wrist pin journal prior to complete failure. Detonation leaves a much finer more evenly...
  3. Thread: 3.3 Failure

    by maxxdrevo
    Replies
    36
    Views
    1,994

    This is a good point and wouldnt ya know.... I...

    This is a good point and wouldnt ya know.... I use a heat gun everytime I start a nitro engine. Like I said I have been around the block..

    220 is perfectly fine IMO with this fuel. I have seen...
  4. Thread: 3.3 Failure

    by maxxdrevo
    Replies
    36
    Views
    1,994

    Its funny that I can tune any of my VSpec's or...

    Its funny that I can tune any of my VSpec's or Piccos or even my other 3.3's and not have a failure yet the consensus says its lean. I have 3 Piccos with over 13 gallons on them, 2 OFNA .12's with...
  5. Thread: 3.3 Failure

    by maxxdrevo
    Replies
    36
    Views
    1,994

    I can understand that situation Snook Man. What...

    I can understand that situation Snook Man. What baffles me is that this mill was not even pushed hard. When it let go it was barely 1/4 throttle. Actually this mill was babied more than any of my...
  6. Thread: 3.3 Failure

    by maxxdrevo
    Replies
    36
    Views
    1,994

    It was broke in with an ambient air temp of 75...

    It was broke in with an ambient air temp of 75 degrees. Temps at the glow plug were 220 degrees. So now tell me it was lean......

    And the day this happened was an ambient temp of 70 degrees....
  7. Thread: 3.3 Failure

    by maxxdrevo
    Replies
    36
    Views
    1,994

    Ok a few questions. Where is it that you see a...

    Ok a few questions. Where is it that you see a chip in the piston head? Also with temps as low as it was how could it be lean? This isnt my first rodeo. For it to be run lean enough for the head...
  8. Thread: 3.3 Failure

    by maxxdrevo
    Replies
    36
    Views
    1,994

    3.3 Failure

    Now Im not trying to start a bashing thread. Im just looking for opinions. Ive been having email problems so I havent been able to email these directly to Traxxas for "expert" advice. This mill...
  9. Replies
    97
    Views
    2,186

    Shreveport, La if someone wants to add me......

    Shreveport, La if someone wants to add me......
  10. Thread: tire glue

    by maxxdrevo
    Replies
    7
    Views
    317

    +1 That Fusion by AKA is unreal. Dont get any...

    +1

    That Fusion by AKA is unreal. Dont get any on ya or you will have a burn mark for days after... :lol: :lol:
  11. Replies
    87
    Views
    5,653

    Jammin X2 CRT, OS VSpec Jammin X1 CR, OS VSpec...

    Jammin X2 CRT, OS VSpec
    Jammin X1 CR, OS VSpec
    Jammin X1 CRT, OS VSPEC
    5308 Revo, Picco Max .26
    5308 Carbon Fiber Revo, Picco Max .26
    Jato 3.3
    OFNA CD3
    EFlite Blade MCX
    EFlite Blade MSR
  12. Replies
    3
    Views
    511

    Been There Done That!!!! Two Times to be exact! ...

    Been There Done That!!!! Two Times to be exact!

    Stay with the FOC with the big block. The TRX C/D doesnt like the torque and HP that the Mid and Big Blocks deliver. I have grenaded 2 C/D's...
  13. With the 007 pipe you may get a slight midrange...

    With the 007 pipe you may get a slight midrange bog... I experienced a little bit of one with it. The 053 is prefered by many but I myself prefer the 086. You really dont need more low end with the...
  14. Replies
    4
    Views
    209

    The M2C chassis brace is a great investment to...

    The M2C chassis brace is a great investment to stiffen the chassis in the engine bay area. It sounds like the cradle is sliding in the mount. Did you remember to install the star washers on each...
  15. Replies
    3
    Views
    226

    The 2 mills are the exact same size. Only...

    The 2 mills are the exact same size. Only difference is in the porting on the crankshaft. If you were limited to 14T/38T with the New Era then I would be looking for a tweaked chassis or possibly...
  16. Replies
    66
    Views
    6,415

    Sig Sauer P2022 9MM ...

    Sig Sauer P2022 9MM

    http://i589.photobucket.com/albums/ss334/spowers00/cid__1224081309.jpg

    Glock Model 22 .40 S&W

    http://i589.photobucket.com/albums/ss334/spowers00/0211081851a.jpg

    Savage...
  17. Replies
    3
    Views
    226

    I didnt have any problems using the stock 3.3...

    I didnt have any problems using the stock 3.3 clutch setup.
  18. Replies
    7
    Views
    451

    C/D is definately worth it with the small block. ...

    C/D is definately worth it with the small block. If you ever decide to step up to a mid or big block then pull the C/D out and install the FOC shaft. I have grenaded 2 C/D's running a Picco .26 but...
  19. Replies
    8
    Views
    504

    I run the TRX CVD's with extended cups. I have...

    I run the TRX CVD's with extended cups. I have no problems at all even with using the Extended Wheelbase Arms set at 19mm. I have never popped one out though I have worn the cups out.....
  20. Replies
    7
    Views
    554

    Im on my 2nd Picco with the same OWB.... First...

    Im on my 2nd Picco with the same OWB.... First Picco I retired at 13 gallons, 2nd now has 6 gallons on it... So thats 19 gallons on a single OWB. I clean and lube the bearing on average about every...
  21. Replies
    7
    Views
    554

    [QUOTE=Klimpen717]Can you show me what roto start...

    [QUOTE=Klimpen717]Can you show me what roto start system you have. Perhaps a link?
    I haven't looked at Hot Bodies yet? What engine do you have?

    Hot Bodies Roto Start


    I run a Picco .26 Max.. ...
  22. Replies
    7
    Views
    554

    I run a Hot Bodies Roto Start with no problems. ...

    I run a Hot Bodies Roto Start with no problems. I have used it with stock arms and the TRX extended wheelbase arms with no problems. I run it with a Vantage CF 3.3 chassis and the stock 3.3 chassis...
  23. Replies
    64
    Views
    3,736

    This X2 has spent quality time on the track under...

    This X2 has spent quality time on the track under another person's control.. I was supposed to race this weekend but had to work. :(
  24. Replies
    64
    Views
    3,736

    Here is another just added to my collection ...

    Here is another just added to my collection

    http://i589.photobucket.com/albums/ss334/spowers00/DSCN0060.jpg
  25. Replies
    7
    Views
    347

    of the 2 listed......Byrons definately

    of the 2 listed......Byrons definately
Results 1 to 25 of 72
Page 1 of 3 1 2 3