Search:

Type: Posts; User: Daedlux

Page 1 of 3 1 2 3

Search: Search took 0.29 seconds.

  1. Replies
    27
    Views
    1,757

    @slaughter33 thanks. I will dremel that out. ...

    @slaughter33 thanks. I will dremel that out. Didnt think of that.

    @hskb
    I ended up using the 2.8 trenchers stretched onto the 3.2 revolvers. Not too much of a weight difference from the 2.8...
  2. Replies
    27
    Views
    1,757

    Does it bend? Instead of break. I haven't seen it...

    Does it bend? Instead of break. I haven't seen it in hand. Nails might work if my hex wasn't so far gone
  3. Replies
    27
    Views
    1,757

    I like going fast. Hehe. But I suppose I should...

    I like going fast. Hehe. But I suppose I should just take it down a bit😓.I dont have any 3s Lipos yet. But I am still open to suggestions because 4s is fun with a lightweight truck.
  4. Replies
    27
    Views
    1,757

    Im cutting nails to use as pins right now. Hope...

    Im cutting nails to use as pins right now. Hope it works
  5. Replies
    27
    Views
    1,757

    Hex pins breaking every run

    Im running a mamba monster with the 2200kv motor on 4s 10000mah lipo. After every bash I end up with only fwd or rwd because im snapping pins inside the hex. 17mm traxxas adapters with trenchers...
  6. Replies
    484
    Views
    22,230

    I broke an mip x-duty cvd. I was jumping a ramp...

    I broke an mip x-duty cvd. I was jumping a ramp and a piece of the wood caught a trencher. Wheel went flying away.

    http://img.tapatalk.com/d11e5b2a-e28c-8800.jpg
    ...
  7. Replies
    3
    Views
    470

    Thank you. Did not see it

    Thank you. Did not see it
  8. Replies
    3
    Views
    470

    Xo-1 Slicks on Slash 4x4 or stampede

    Has any one put xo-1 slicks on a stampede/Slash for street runs?
    Im looking to pick up a set off the bay but wanted to get some opinions on the matter. I finally seen them up close. Size difference...
  9. Replies
    26
    Views
    2,701

    My trenchers baloon huge on 4s lipo. A whole lot...

    My trenchers baloon huge on 4s lipo.
    A whole lot more than the talons. They are Different rubber compounds.
  10. Replies
    484
    Views
    22,230

    I thought this was worth sharing. I broke the...

    I thought this was worth sharing. I broke the slipper input shaft and shedded a motor mount bearing. Almost landed It.

    http://img.tapatalk.com/a6934819-88fa-5183.jpg
  11. Replies
    8
    Views
    525

    Stretched 2.8 trenchers on 3.2 RPM revolvers....

    Stretched 2.8 trenchers on 3.2 RPM revolvers.
    17mm hex. I was actually able to go through my lipos running 4s.

    http://img.tapatalk.com/a6934820-519f-d05c.jpg
  12. Replies
    8
    Views
    525

    I was thinking of getting xo-1 wheels w/ 17mm...

    I was thinking of getting xo-1 wheels w/ 17mm hex. Im not sure what tires I would be able to run them with. I have stripped 5 wheels out now with a similar setup. I have aluminum hex's and tighten...
  13. Replies
    5
    Views
    560

    http://img.tapatalk.com/d11e5db4-73a1-6127.jpg ...

    http://img.tapatalk.com/d11e5db4-73a1-6127.jpg


    First pic could not be viewed
  14. Replies
    5
    Views
    560

    I used my proline stampede body. ...

    I used my proline stampede body.

    http://img.tapatalk.com/d11e5db
    4-7322-414c.jpg

    I cut new holes in the very back of the bed.


    http://img.tapatalk.com/d11e5db4-735d-9927.jpg
  15. Thread: my new truck

    by Daedlux
    Replies
    19
    Views
    1,393

    I did the slash chassis conversion and it makes...

    I did the slash chassis conversion and it makes it handle so much better. I have mip axles all the way around. The fronts rub the aluminum steering blocks. Not too bad. It will grind it down to...
  16. Replies
    65
    Views
    6,584

    I have stripped 4 wheels out in two days on 4s...

    I have stripped 4 wheels out in two days on 4s lipo. This motor is beast. Im still waiting on my 3.2 revolvers with the 17mm hex. Hopefully those will be strong enough.

    @Rc-Fan
    What wheels are...
  17. Replies
    65
    Views
    6,584

    Im running with the slash chassis converted from...

    Im running with the slash chassis converted from the stampede. After a bunch of speed runs and messing around on 4s temps were awesome. Barely over 105 on both esc and motor geared 18/54. I did not...
  18. Replies
    65
    Views
    6,584

    Im excited to see how its going too. I just put...

    Im excited to see how its going too. I just put the 2200kv in my xl pede but cant run it till I get some c-hubs. Will post pics and a running video real soon.
  19. Replies
    8
    Views
    684

    The pin and the drive cup broke. Good idea with...

    The pin and the drive cup broke.
    Good idea with the nail.
  20. Replies
    8
    Views
    684

    Yeah a bit. I was trying to prevent it from...

    Yeah a bit. I was trying to prevent it from nosediving. I guess I will give the summit shafts a shot.
  21. Replies
    8
    Views
    684

    Broke traxxas cvd's on 4s

    I just got this erevo yesterday. Upgraded to cvds all the way around including the center shaft. Doing speed runs was all good but a couple of good jumps is all it took.
    ...
  22. Replies
    65
    Views
    6,584

    I like launching it and bashing around on my...

    I like launching it and bashing around on my backyard track. I dont really have space to get up to speed but really also just want a cool running reliable motor/esc combo to bash with. I didnt say...
  23. Replies
    65
    Views
    6,584

    @ Rc Fan. Have you clocked this setup on a gps...

    @ Rc Fan. Have you clocked this setup on a gps or radar?
  24. Replies
    10
    Views
    958

    Thanks for the info. Thats about what Im looking...

    Thanks for the info. Thats about what Im looking to get out of it. With brutal torque through most of the run.
  25. Replies
    10
    Views
    958

    So what kind of speed could I expect from the...

    So what kind of speed could I expect from the 2400kv extreme sct setup?
    Geared 21/54 with 4s lipo.
Results 1 to 25 of 60
Page 1 of 3 1 2 3