Search:

Type: Posts; User: bigdannyb

Search: Search took 0.18 seconds.

  1. Replies
    2
    Views
    493

    large tires for stampede

    I was wondering if there were any 3.8 rims with an offset that would allow me to mount them on my stampede? I have two sets of stock e-revo tires, but would need rims to mount up these tires. I do...
  2. Replies
    8
    Views
    481

    lipo question

    I have some 6000mah, 2 cell batteries. When charging my charger shuts off at 6000mah, but the voltage per cell is in the 4.15-4.17 range. So I restart my charger and it puts in around 450mah before...
  3. Replies
    12
    Views
    958

    I haven't tried either tire, but a buddy has the...

    I haven't tried either tire, but a buddy has the badlands on e-revo with a novak brushless system. That thing is nearly impossible to flip during turns both under power and braking. After 30,000 mah...
  4. I have taken one of my 1200 mah merv batteries...

    I have taken one of my 1200 mah merv batteries and taped it to the battery hold down clip, and power my two fans from that. A traxxas end and some soldering and the two fans cook really well. It's...
  5. Replies
    11
    Views
    537

    looks like i might just bite the bullet, fix all...

    looks like i might just bite the bullet, fix all four corners, and be one step closer to bullet proof. Thanks
  6. stock 11 tooth pinnion, and 54 spur, on 3s in my...

    stock 11 tooth pinnion, and 54 spur, on 3s in my truck has sent the temp to 200, I know thats to hot, but she still rips.
    I now run a heat sink/fan on motor, and have an esc fan on order, with a 9...
  7. Replies
    11
    Views
    537

    Worth the extra cash?

    Just out goofing around on 3s, and somehow threw the struck into a massive cartwheel. 6 feet in height and 15 feet in distance equals broken caster block 6832, and steering block6837, both stock. ...
  8. Replies
    2
    Views
    355

    Did you check the hex pins? I had the same thing...

    Did you check the hex pins? I had the same thing happen to me.
  9. Replies
    5
    Views
    346

    thanks for the advice, do you feel it would be...

    thanks for the advice, do you feel it would be better to charge at 4.0 amps just so the charger isn't at maximum strain?
  10. Replies
    5
    Views
    346

    I have the stock velenion esc and motor, and he...

    I have the stock velenion esc and motor, and he is running a sidewinder system. My esc normally cuts out at around 3.55v give or take. Shouldn't a charger with less w/a only take a longer time frame...
  11. Replies
    5
    Views
    346

    Lipo capacity question

    I have 2 gens ace 5300-7.4-30c batteries. When I charge both of these batteries, I almost never see more than 4950 mah get charged back into them. Both cells reach their 4.2v capacity, on both...
  12. Thread: bb question

    by bigdannyb
    Replies
    4
    Views
    342

    bb question

    My merv likes to run hot, heat sink on the motor, but 3s pretty much puts the esc into thermal. I have a full 3500 velenion motor/esc combo from a slash 4x4, plus a tembol mount.

    Before I hack up...
  13. Replies
    6
    Views
    498

    It was 20 celcius today, and I know I have had...

    It was 20 celcius today, and I know I have had thermal shutdown with temps alot lower than today was, ran 23 pinion yesterday and thermal shutdown once on 3s only halfway through the battery life, 20...
  14. Replies
    6
    Views
    498

    merv vs big brother

    Today I took my merv out and met up with a buddy who has two slash platnums and the big boy, Mr E Revo1/10.

    After a few minutes it was time to put the brothers side by side on the starting line....
  15. Replies
    10
    Views
    1,496

    that t-bone looks like the answer, shim kit I...

    that t-bone looks like the answer, shim kit I already have, looks like it is time to go shopping.
    Thanks for the insite, I also appreciate the part numbers aswell.
    Dan
  16. Replies
    2
    Views
    369

    motor temp near 200

    I was goofing around with my pede, and the motor or something in the drive train started to make a funny sound. Took it down stairs and checked the motor temp and it was right at 200, esc was at 149....
  17. Replies
    10
    Views
    1,496

    Broken rear bulkhead

    I was putting on some rpm A arms and noticed that my rear bulkhead is cracked and broken into about 6 pieces, and this only after 6 or so drives. Should I replace it with an aluminum bulkhead, or...
  18. Replies
    4
    Views
    254

    Ya, wasn't a total waste of time, since I had it...

    Ya, wasn't a total waste of time, since I had it torn down, I took this time to put in my aluminum shock towers, rpm a arms and front mip x duties. Now just waiting for lhs to open so I can order...
  19. Replies
    4
    Views
    254

    Thanks for that Strykeviper, I wish I had posted...

    Thanks for that Strykeviper, I wish I had posted this question before tearing half my truck apart, looks like I had a stripped stock hex head(inside where the little pin goes). Thanks for the reply....
  20. Replies
    4
    Views
    254

    vxl driveline issues

    Hey all, new to this rc hobby, having alot of fun but ran into an issue. New pede only a month old and more or less have front wheel drive only.
    Pulled the slipper out and lots of meat there, mip...
Results 1 to 20 of 20