Search:

Type: Posts; User: Mr_Zed_ZX20

Page 1 of 4 1 2 3 4

Search: Search took 0.22 seconds.

  1. Replies
    33
    Views
    1,842

    How is your spur gear holding up? I'm having all...

    How is your spur gear holding up? I'm having all kinds of issues with mine stripping out almost immediately. I'm now considering going to a hardened steel spur and clutch bell just to end the...
  2. Ask and you shall receive, lol. ...

    Ask and you shall receive, lol.

    http://i204.photobucket.com/albums/bb261/Doc-Savage/P4150002_zpsbb44b11b.jpg

    http://i204.photobucket.com/albums/bb261/Doc-Savage/P4150001_zps83801bea.jpg

    Its...
  3. Dunno if you already did this, but a cheap way to...

    Dunno if you already did this, but a cheap way to lighten up the plastic is to use the slayer pro radio, servo, battery mount. I think I bought mine for about $15 shipped. It gets rid of the bulky...
  4. thanks for doing this build up as I too have a...

    thanks for doing this build up as I too have a special place in my heart for the MT class of racing. And while I am all about putting the truck on a diet, its worth mentioning that sacrificing weight...
  5. sounds like you're on top of things, glad to see...

    sounds like you're on top of things, glad to see you've figured it out. If you're wanting to go "above and beyond" you could do the ceramic bearing mod on the old crankcase. the lighter bearings not...
  6. Good deal, I'll definitely look into the clutch...

    Good deal, I'll definitely look into the clutch system. I will admit, my seat time with the revo platform is limited (I've owned it for 5yrs and still haven't put a whole gallon through it). So now...
  7. Many thanks, I totally forgot about Hot Racing....

    Many thanks, I totally forgot about Hot Racing. As far as gearing goes, it has the short ratio gear stack at the moment which I plan to pull out in the near future. I've looked at the RRP extra hard...
  8. Do yourself a favor and spend the money on a...

    Do yourself a favor and spend the money on a bottle of after run oil and leave the wd-40 for your bicycle chain. While the manufacturer says it has corrosion inhibiting properties, that doesn't mean...
  9. I've only seen that when the high shock loads...

    I've only seen that when the high shock loads were placed on the clutch. A good example of this would be when you land after a jump with the throttle pinned. The clutch is engaged and the stress is...
  10. First its important to verify which type of...

    First its important to verify which type of failure you are referring to. Mechanical failure will be as previously mentioned with side to side play. Sealing failure will come from the seals no longer...
  11. Replies
    27
    Views
    682

    Having owned an original slayer, 3.3 revo, and...

    Having owned an original slayer, 3.3 revo, and now an E-slayer pro I can tell you the original slayer leaves a lot to be desired in terms of handling and ground clearance under the skid plates. The...
  12. Replies
    8
    Views
    129

    In that case, yes, its very bad and things will...

    In that case, yes, its very bad and things will go BOOM if you don't max out the credit card immediately, lol.
  13. Picco .28 and stripped spur gears Help!?

    Hello everyone, I seem to have come across a problem that I can't seem to figure out. I've recently put a P3-28 Picco engine in my revo and it's going through spur gears very quickly (within the...
  14. Replies
    13
    Views
    418

    Its kinda irrelevant really, the plugs on the...

    Its kinda irrelevant really, the plugs on the receiver are all bussed together so any additional load is going to be seen regardless of where its placed.
  15. Replies
    3
    Views
    249

    I did the mod to my low gear only and you will...

    I did the mod to my low gear only and you will still have "some" slop, but its not as bad. Just be aware that you will have a slightly harder time shifting out of low gear when their is a load on...
  16. Replies
    9
    Views
    270

    My suggestion would've been to swap the new servo...

    My suggestion would've been to swap the new servo with the old one that controls the gear selection; that way you would still have the servo saver feature that's installed on the front diff locker...
  17. That mod should do well to keep the previously...

    That mod should do well to keep the previously hollow portion of the shaft from collapsing. I'm going to assume you have your slipper clutch set fairly tight.
  18. Replies
    48
    Views
    2,680

    the easy fix for that is to buy a set of extended...

    the easy fix for that is to buy a set of extended hexes, I used the integy +3mm 17mm hexes. They make them in +6mm too. I don't know if that is enough to give you the clearance you wanted, but I...
  19. Replies
    30
    Views
    869

    Nothing, its just a difference of terms to...

    Nothing, its just a difference of terms to describe the same thing. Heavy spring means its able to support more load, stiff spring means its more resistant to compression which in turn means it can...
  20. Replies
    47
    Views
    3,788

    Off topic, but I thought I'd share. I'm still...

    Off topic, but I thought I'd share. I'm still unpacking boxes from my recent move and came across a little surprise. Years ago I bought the original Traxxas Slayer. It was completely original at...
  21. Replies
    47
    Views
    3,788

    A little update, I still haven't got any videos...

    A little update, I still haven't got any videos of my truck in action and its not for a lack of trying. Apparently my GoPro was set to take pics instead of videos so all I got out of a 4hr day was...
  22. Replies
    22
    Views
    1,755

    Very nice, when I saw your buggy it screamed to...

    Very nice, when I saw your buggy it screamed to me Mad Max, Beyond Thunderdome when they had all the crazy looking desert machines.
  23. Replies
    26
    Views
    1,395

    Yeah, the F-11's are sweet. I bought 2 sets from...

    Yeah, the F-11's are sweet. I bought 2 sets from my LHS and thought they were a discontinued style as I had never seen them before. I wanted to mount them to the Duratrax truggy tires, but...
  24. Replies
    44
    Views
    1,901

    I'm running the variable dampening pistons in my...

    I'm running the variable dampening pistons in my summit and love them. In a nutshell, they make the shock stiffer (slower) on compression and faster on rebound. I like it because it allows me to...
  25. Motor/ESC: MMM 2200kv (soon to be RX8 & 2100kv...

    Motor/ESC: MMM 2200kv (soon to be RX8 & 2100kv sensored motor)

    Radio: 2.4gHz Traxxas, 4 wheel steering computer from Common Sense RC, CC BEC set at 6.0v

    Servos: Stock for...
Results 1 to 25 of 76
Page 1 of 4 1 2 3 4