Search:

Type: Posts; User: malonefamily2003

Page 1 of 18 1 2 3 4

Search: Search took 0.12 seconds.

  1. Replies
    489
    Views
    31,369

    I fixed the wheel slop a few months ago on my...

    I fixed the wheel slop a few months ago on my stock Summit. Stopped at the hobby shop today and picked up some of the HPI 5mm wheel nuts # Z682. Remove the hex adapters and cut half the threads off...
  2. Replies
    489
    Views
    31,369

    Got some paint as close to Overkill awhile back...

    Got some paint as close to Overkill awhile back and just got around to trying it out. Painted the bead lock rings and a set of center caps and of course i added the Ford emblems.
    ...
  3. Replies
    489
    Views
    31,369

    Ordered an aluminum steering holder from the same...

    Ordered an aluminum steering holder from the same company that makes the servo saver I just installed. Trying to talk the wife into letting me order some blue aluminum shocks from Integy.
  4. I would go ahead and get the field programmer too...

    I would go ahead and get the field programmer too . It's only like 10 bucks and comes in handy when your not near a computer .
  5. Replies
    489
    Views
    31,369

    It's made by a company called Blitz . I got it...

    It's made by a company called Blitz . I got it off E Bay.
    ...
  6. Replies
    489
    Views
    31,369

    The kids enjoy going to the skate park but...

    The kids enjoy going to the skate park but OVERKILL not so much. All the kids were taking turns flying through some loose dirt. After a few doughnuts OVERKILL flips over and blows the shock cap off ....
  7. Replies
    6
    Views
    73

    Hot Racing did make some slider shaft for the...

    Hot Racing did make some slider shaft for the merv that would work but they change their design and now use dog bones shafts that dont fit just right. I'm still trying to find a set of the old ones...
  8. Replies
    6
    Views
    73

    I switched to the merv shafts about 2 weeks ago...

    I switched to the merv shafts about 2 weeks ago and they pop a joint every time it flips over or i pull a wheelie . Its really annoying but they just pop back in .
  9. Replies
    9
    Views
    500

    Didn't get to order those sliding shafts by the...

    Didn't get to order those sliding shafts by the time I got around to it they had sold and were the last on eBay. I ended up buying the merv plastic shafts . I pop the joint out every 5 mins which...
  10. Replies
    489
    Views
    31,369

    Stripped the servo horn and one of the shock...

    Stripped the servo horn and one of the shock retainers collapsed .
  11. Replies
    489
    Views
    31,369

    Time to order more parts . ...

    Time to order more parts .

    http://youtu.be/0GMXk5wQ_Wo
  12. Replies
    1
    Views
    135

    Its fine just don't pull lots of weight for long...

    Its fine just don't pull lots of weight for long periods of time. I pull my 6 yr old twins around the yard all the time .
  13. Replies
    489
    Views
    31,369

    Ordered a servo saver for Overkill last week and...

    Ordered a servo saver for Overkill last week and installed it today. Its made from 7075 T6 heat treated aluminum so it should hold up. Everything went together nice and tight with no slop ....
  14. I would try some thicker lube on the bushings and...

    I would try some thicker lube on the bushings and if that dont help drive it like you stole it until it dies for good. Replacement motors are around 30 bucks which is not bad. After a few 775's you...
  15. They are big and heavy but not one snapped axle...

    They are big and heavy but not one snapped axle or drive shaft yet. 2 rear diffs and steering arms so far.
  16. Replies
    11
    Views
    260

    I have 2 of the Savox 1230 and they are tough but...

    I have 2 of the Savox 1230 and they are tough but not waterproof . Kids buried their Summit up to the windshield in a big mud hole. After sitting a day or 2 it started glitching when I powered the...
  17. Replies
    9
    Views
    268

    Maybe LEM will make some in 7075 and make them...

    Maybe LEM will make some in 7075 and make them look purdy ...
  18. Replies
    9
    Views
    268

    Have not seen the ones from HR yet . I wonder if...

    Have not seen the ones from HR yet . I wonder if they are made from the same aluminum 6061 or the stronger stuff?
  19. Replies
    9
    Views
    268

    Integy aluminum bulkhead

    Just wondering if anyone has tried the Integy aluminum bulkheads and if they are worth the money and time?
  20. Super Swampers for my Summit and stock tires for...

    Super Swampers for my Summit and stock tires for the kids Summit. Working on some cool tires for the kids Summit they will be taller then the Super Swampers but much lighter.
    ...
  21. Replies
    5
    Views
    237

    I have the Kershaw Design chassis and like the...

    I have the Kershaw Design chassis and like the looks of it. The main reason i bought it was so i could run larger batts. Shortly after buying the chassis i used it as a template to make another...
  22. They could go to the skid plates also. I know the...

    They could go to the skid plates also. I know the skids kinda snap into place over the A-arm pins. Each skid plate should have 4 bolts about that size.
  23. Replies
    489
    Views
    31,369

    Trail ride from OVERKILLS view. ...

    Trail ride from OVERKILLS view.

    http://youtu.be/KUbk12PpB3c
  24. Replies
    8
    Views
    170

    Pretty much what I'm hoping will happen ??? This...

    Pretty much what I'm hoping will happen ??? This way I can apply more pressure to the 3 clutch pads. It should still slip and shouldnt be locked it will just take a lot more force to get it to slip.
  25. Replies
    8
    Views
    170

    I don't think it's a good idea to have pressure...

    I don't think it's a good idea to have pressure on either race that will throw it out of alignment just the slightest bit. My plan is to use 2 washers stacked on top of each other soldered together ....
Results 1 to 25 of 437
Page 1 of 18 1 2 3 4