Search:

Type: Posts; User: superfly13_69

Page 1 of 11 1 2 3 4

Search: Search took 0.18 seconds.

  1. Replies
    4
    Views
    251

    You'll get faster acceleration with them. I put...

    You'll get faster acceleration with them. I put them on and immediately noticed a difference. Alot prettier too.
  2. Replies
    2
    Views
    171

    You could solder it, but personally I'd get a new...

    You could solder it, but personally I'd get a new one. There's two routes:

    Buy a replacement receiver... $22 at Tower:
    http://www2.towerhobbies.com/cgi-bin/wti0001p?&I=LXSP02&P=

    Or, measure...
  3. Replies
    6
    Views
    330

    No way those will fit. They're for the Mini-T. ...

    No way those will fit. They're for the Mini-T. I think that's 1/18 scale. You could shoot hoops in your Dirt Hawgs with those. Look at the dimensions. They're only just over 1" tall & wide.
  4. Replies
    7
    Views
    211

    Sounds like a glow wire issue. Check both ends....

    Sounds like a glow wire issue. Check both ends.

    Check your EZ-start pack too. Look in there and make sure the little metal tube isn't pushed back.
  5. Replies
    8
    Views
    315

    People normally break 2nd gear, not 1st. Either...

    People normally break 2nd gear, not 1st. Either way, cracking into the tranny is annoying and tedious. Just make sure you don't forget there's two screws under the tranny holding the rear...
  6. Thread: breaks

    by superfly13_69
    Replies
    6
    Views
    341

    Setting them up correctly has a lot more to do...

    Setting them up correctly has a lot more to do with it, IMHO.
  7. Replies
    5
    Views
    294

    Mystic, check your chassis. I have this same...

    Mystic, check your chassis. I have this same problem, but it's because of a bent chassis, right in front of the engine.
  8. Replies
    42
    Views
    980

    I'd say about 1/2 to 2/3 of this forum thinks...

    I'd say about 1/2 to 2/3 of this forum thinks it's a good thing. That's proof enough for me, besides the fact that I've done it 3 times on one set of rims and they're still going strong bashing...
  9. Replies
    42
    Views
    980

    You won't find an easier way than that....

    You won't find an easier way than that....
  10. Replies
    27
    Views
    934

    Either grass or dirt, Speed paws won't turn very...

    Either grass or dirt, Speed paws won't turn very well. Get some good Edge's. They hook up well on grass, and outstanding on dirt.

    http://www2.towerhobbies.com/cgi-bin/wti0001p?&I=LXFHL7&P=7
  11. Replies
    2
    Views
    235

    The only reception problems I ever had was when...

    The only reception problems I ever had was when my transmitter batteries were low. The red light flashes when that happens.
  12. Replies
    17
    Views
    316

    I know mine makes some sort of "clankle" sound at...

    I know mine makes some sort of "clankle" sound at idle, and I know my clutchbell bearings are starting to wear. The vibration of idle makes every little thing very noticeable.
  13. Thread: sick!!!

    by superfly13_69
    Replies
    7
    Views
    272

    You know, a simple countersink is to get a drill...

    You know, a simple countersink is to get a drill bit just the right size and drill it to the depth you want.
  14. Thread: sick!!!

    by superfly13_69
    Replies
    7
    Views
    272

    The front would be useless if you get the RPM...

    The front would be useless if you get the RPM wide bumper, because that's built into the plastic. I like the rear, though. My chassis looks pretty scraggly back there from bashing and scraping.
  15. Replies
    18
    Views
    1,241

    What does the plug look like when it blows? ...

    What does the plug look like when it blows? Dark? (too rich) Bluish gold tinge? (overheating)

    Make sure you're using a quality plug. I personally like the OS A5. It's made for high temp truck...
  16. Replies
    10
    Views
    233

    I'd watch out going aluminum with hexes. I'd...

    I'd watch out going aluminum with hexes. I'd rather strip out a $.99 hex than a $5-10 rim (+ $12 tire) any day of the week.
  17. Replies
    17
    Views
    345

    Yeah, the oven literally bakes the glue, so it's...

    Yeah, the oven literally bakes the glue, so it's crispy. SOOOO much easier to pull off than boiling. I personally use alot of glue so I leave mine in at 275deg for about 20 minutes. Doesn't hurt...
  18. Replies
    3
    Views
    244

    Normally, the only difference between a stadium...

    Normally, the only difference between a stadium truck and a buggy is the front tire size, front suspension geometry, and maybe a little wheelbase. And of course the body.
  19. Replies
    15
    Views
    305

    I'd go with the WD-40 also. Oil will just make...

    I'd go with the WD-40 also. Oil will just make dirt stick.
  20. Replies
    8
    Views
    1,623

    Yep, that's it. Actually it's the OWB and the...

    Yep, that's it. Actually it's the OWB and the plastic gear. They come apart. Here's a replacement from Tower. (yes it's the same part for the 2.5 and 3.3)
    ...
  21. Replies
    12
    Views
    1,455

    No, didn't use the OWB. I just used a bell nut...

    No, didn't use the OWB. I just used a bell nut that would fit in the place of the OWB, drilled a hole thru that, and pressed in a suitable shaft. I did drill a hole thru the back of the EZ-start...
  22. Replies
    8
    Views
    259

    I run a S3004 in throttle, and HS5625MG in the...

    I run a S3004 in throttle, and HS5625MG in the steering. The HS isn't metal case, but it's metal gear. No probs in a year and still going strong.

    Congrats on getting back from Iraq, BTW.
  23. Replies
    8
    Views
    1,623

    You only have to remove the exhaust to get to the...

    You only have to remove the exhaust to get to the ez-start. Two screws for the exhaust, and 3 for the ez-start.
  24. Replies
    4
    Views
    192

    Get a MG servo and save yourself some headaches. ...

    Get a MG servo and save yourself some headaches. Hitec 5625MG works well for me.
  25. Replies
    8
    Views
    1,011

    No aluminum that I know of. Some guys get a...

    No aluminum that I know of. Some guys get a sheet of CF and make their own.
Results 1 to 25 of 264
Page 1 of 11 1 2 3 4