Search:

Type: Posts; User: Maxxturbo

Search: Search took 0.04 seconds.

  1. Replies
    10
    Views
    202

    removing driveshaft need a little help

    Hi everyone,
    i am trying to replace one of the front drive shafts on my t-maxx 3.3 and following the instructions with the part, i removed the wheel, axle pin and hex hub..however how can i remove...
  2. Replies
    3
    Views
    181

    thankyou everyone.

    thankyou everyone.
  3. Replies
    3
    Views
    181

    Please help - Picture included

    I got a body for a used truck , The guy told me it is a 3.3, All the body posts and mounts line up perfectly except the exhaust pipe. Can you please look at let me know if i have the wrong exhaust?
    ...
  4. Replies
    4
    Views
    353

    All is good it worked. Thanks once again

    All is good it worked.
    Thanks once again
  5. Replies
    4
    Views
    353

    ok thanks I will try and let you know how it went.

    ok thanks I will try and let you know how it went.
  6. Replies
    4
    Views
    353

    Help wanted to unscrew rear shocks

    Can anyone please advice the best or easiest way to unhook the rear shocks, the set that is closes to the engine?
    On one side the muffler is blocking one screw and on the otherside it is the gas...
  7. Replies
    7
    Views
    141

    Oh really glad to hear it worked then!! one of...

    Oh really
    glad to hear it worked then!! one of my plugs is missing a connector from the prvious owner i am trying hard to find this one for now i just wrapped it around the ez start motor does the...
  8. Replies
    7
    Views
    141

    Yes looks like that , one way bearing.

    Yes looks like that , one way bearing.
  9. Thread: Wheelies

    by Maxxturbo
    Replies
    8
    Views
    417

    Wheelies

    How Do i get my t-maxx to pop wheelies, the front end will not go up. Maybe I could tune it better?

    I dont know what I am doing wrong.
  10. Replies
    2
    Views
    187

    Is the filter clean ? So you got the motor to...

    Is the filter clean ? So you got the motor to start finally? but it goes very slow is that the problem?
  11. Replies
    16
    Views
    391

    The 240 piece screw kit looks amazing. ! nice...

    The 240 piece screw kit looks amazing. ! nice screws
  12. Replies
    16
    Views
    391

    Ok thanks a lot,i got this truck used ( big...

    Ok thanks a lot,i got this truck used ( big mistake to make ) now i am left someones problem, someone who didnt know what they were doing and put any screw anywhere. So i will order the tony's screws...
  13. Replies
    16
    Views
    391

    Thats a great idea , I will try that. I never...

    Thats a great idea , I will try that. I never thought of that.
    Thankyou everyone , this place is so helpful it is unbelieveable.
    I will let you know how it goes.
  14. Replies
    16
    Views
    391

    Hi Everyone Here are the pictures of the...

    Hi Everyone

    Here are the pictures of the screws I need help removing. If you could please take a look and provide some assistance on how to remove them...
  15. Replies
    16
    Views
    391

    I will post a picture today , thankyou all for...

    I will post a picture today , thankyou all for your help
  16. Replies
    16
    Views
    391

    If you look at the t-maxx from the bottom where...

    If you look at the t-maxx from the bottom where the brace fixes to the chassis , I am looking at one of the screws there
  17. Replies
    16
    Views
    391

    You mean cut a slot where the head is missing or...

    You mean cut a slot where the head is missing or the other side? Basically there is no head. just the shaft
  18. Replies
    16
    Views
    391

    Stripped screw for lower chassis brace

    Hey Everyone

    What would you recommend to remove a screw with no head on it:confused:

    Thanks
  19. Thread: steering

    by Maxxturbo
    Replies
    8
    Views
    243

    I would like to know as well.

    I would like to know as well.
  20. Thread: steering

    by Maxxturbo
    Replies
    8
    Views
    243

    thanks so much, I will use what I bought and then...

    thanks so much, I will use what I bought and then try out the aluminium one.
  21. Thread: steering

    by Maxxturbo
    Replies
    8
    Views
    243

    I got the hitec 5345 X Lincoln87, is there a...

    I got the hitec 5345 X Lincoln87, is there a special horn ?
  22. Thread: steering

    by Maxxturbo
    Replies
    8
    Views
    243

    Hi Wildman4910 thanks for the assistance I am...

    Hi Wildman4910

    thanks for the assistance I am using a hitec5645mg , The link from towerhobbies is a round servo saver I think my t-maxx 4907 uses a different kind like a u-shaped one ,do you know...
  23. Thread: steering

    by Maxxturbo
    Replies
    8
    Views
    243

    steering

    I bought a used maxx and found out that my steering servo is broken. What do you guys recomend as an upgrade for a servo saver, when i hooked up a new servo the screw is moving but the wheels are not...
Results 1 to 23 of 24