Search:

Type: Posts; User: TRXproskills

Page 1 of 8 1 2 3 4

Search: Search took 0.19 seconds.

  1. Replies
    0
    Views
    811

    Running 5s and problem

    The non-Traxxas support question(s) have been removed.

    The type of support sought by this post was of a non-Traxxas nature. Please contact the manufacturer of your battery packs and/or charger for...
  2. Replies
    3
    Views
    1,004

    traxxas big bores are good shocks for jumping etc...

    traxxas big bores are good shocks for jumping etc because they are nice and smooth and i think strong but piggybacks look good and are good shocks untill they start to leak
  3. Replies
    16
    Views
    739

    wow what a story glad to hear you found it

    wow what a story glad to hear you found it
  4. Replies
    3
    Views
    263

    i have never had any problems with stock shaft on...

    i have never had any problems with stock shaft on 6s lipo maybe if you install steel drive shafts you will start to destroy diffs?
  5. Replies
    12
    Views
    1,789

    Make sure the half shaft screws or cvd screws are...

    Make sure the half shaft screws or cvd screws are tight as sometimes then can come loose and catch
  6. Replies
    5
    Views
    946

    i have dual rate springs on traxxas big bore...

    i have dual rate springs on traxxas big bore springs and 60w oil and seems to be fine for smaller to medium jumps :D
  7. Replies
    26
    Views
    1,810

    i have rpm a arms with traxxas hubs and cvd's and...

    i have rpm a arms with traxxas hubs and cvd's and no problems
  8. Replies
    9
    Views
    1,599

    i would go for some cheap 5200mah 7.4v lipos from...

    i would go for some cheap 5200mah 7.4v lipos from HK it takes about 3 and half weeks max to arrive in uk wich isnt that bad if you forget about it, i use this charger it works well can can charge to...
  9. Replies
    2
    Views
    921

    ok Thanks for your help

    ok Thanks for your help
  10. Replies
    2
    Views
    921

    motor quickie

    What type of connector do the titan 550 motors have on them im afer buying new ones, also what gage wire is it. Thanks
  11. Replies
    10
    Views
    1,229

    best way is to just push a 2mm allen key through...

    best way is to just push a 2mm allen key through the tyre in 2 or 3 places ive done it to most of my tyres and lets all the water out and none of my tyres have ripped
  12. Replies
    5
    Views
    1,058

    best go for the newer e-maxx with water proof esc...

    best go for the newer e-maxx with water proof esc and get 2.4ghz radio if you can
  13. Hi, guys found the "aching" problem a chipped...

    Hi, guys found the "aching" problem a chipped tooth lol yeah the tooth in the diff had chipped and then the chipped part damaged the other teeth :S i did a video of the click when the diff was...
  14. Replies
    25
    Views
    4,437

    the soldering can be tricky because the turnigy...

    the soldering can be tricky because the ******* 5200 30c lipos batts have realy thick wires and you will have a *** on getting them to go into the traxxas connector houseing it took me ages to do haha
  15. Replies
    4
    Views
    925

    make sure that you tighten the little grub screws...

    make sure that you tighten the little grub screws down onto the flat spot on the shaft from the motor because its sounds a little bit unusual that bouth should come off at the same time
  16. thanks for help im going to have a look at it as...

    thanks for help im going to have a look at it as soon as i get home on friday, i already have a diff spare so if i need it its there, i dont think that it is the diff because useualy it would have...
  17. Replies
    2
    Views
    966

    nice trucks

    nice trucks
  18. Replies
    3
    Views
    967

    it should be fine it is just there to help...

    it should be fine it is just there to help prevent dirt and grit from getting into the splines of the drive shaft
  19. Clicking noise unknown blown diff?? with vid

    Hey,
    I have a traxxas e-maxx with mamba monster running 4s and it is clicking badley it sounds like it could be something like a drive shaft pin coming loose and catching or the rear diff before it...
  20. Replies
    6
    Views
    328

    3.3 is quite a good engine, parts are easy to get...

    3.3 is quite a good engine, parts are easy to get hold of from ebay for good prices,
  21. Thread: Smoking

    by TRXproskills
    Replies
    6
    Views
    224

    as said the engine could be overheating things...

    as said the engine could be overheating things you could check is if the glow plug washer is installed correctly and the glow plug is tight because it could be letting little bit of fuel out to the...
  22. Replies
    2
    Views
    179

    make sure that your throttle trim is set to 0 and...

    make sure that your throttle trim is set to 0 and try again or try re calibrating the transmitter to the esc
  23. Replies
    53
    Views
    7,162

    hi where did you buy these wheels and tyres from...

    hi where did you buy these wheels and tyres from i also live in uk and know how hard it is to get these sort of items, thanks
  24. Replies
    3
    Views
    1,813

    Trading mamba monster for evx.....

    the snow is here in the UK and im wanting some advice on what to do on changing to a water proof system, im not interested in messing with the mamba monster esc trying to water proof that so ive...
  25. Replies
    10
    Views
    1,141

    ive managed to get it sorted out by downgrading...

    ive managed to get it sorted out by downgrading the firmware but i still dont understand how newer firmware would cause this problem.
Results 1 to 25 of 193
Page 1 of 8 1 2 3 4