Search:

Type: Posts; User: wagnman

Search: Search took 0.00 seconds.

  1. I have a 2009 Ford FG G6et that's pretty bombed...

    I have a 2009 Ford FG G6et that's pretty bombed out.

    Makes 505HP at the rear tyres, has a heap of mods and goes VERY hard.
  2. Replies
    23
    Views
    2,387

    Body ! That will be sick

    Body ! That will be sick
  3. Replies
    7
    Views
    475

    Soft suspension helps too.

    Soft suspension helps too.
  4. Replies
    15
    Views
    1,055

    Hey absoloot is there any chance you could give...

    Hey absoloot is there any chance you could give me the part numbers for your slipper / spur and pinion set up? Cheers in advance for your help.
  5. Replies
    26
    Views
    1,435

    The traxxas wheelie bar is junk, honestly. It...

    The traxxas wheelie bar is junk, honestly. It won't break easy but it's frustrating because it UN clips itself and ends up dragging along the ground doing nothing so you have to cone back and re...
  6. Replies
    15
    Views
    1,055

    I'm not sure about the std Trans case but I put a...

    I'm not sure about the std Trans case but I put a 1965Kv 1/8 scale HPI flux motor in my rusty and all I had to do was cut a section out off the bottom on the trans case as the big motor hit on the...
  7. Thread: Why Me?

    by wagnman
    Replies
    16
    Views
    1,032

    I am incredibly touched by you're story. Please...

    I am incredibly touched by you're story.
    Please don't blame yourself, there is nothing you could have done that would have changed what happened.
    You were obviously a good friend. Unfortunately...
  8. Replies
    30
    Views
    1,275

    The sc8 hobbywing esc is very good but be aware...

    The sc8 hobbywing esc is very good but be aware that they only recommend 4s for low Kv motors. You will need to check it out to see what they recommend with your motor. Its a great esc though, I had...
  9. I have found that putting a little but of Loctite...

    I have found that putting a little but of Loctite on the motor shaft before I put the pinion on helps alot, and don't forget to Loctite the pinion grub screw as well
  10. Replies
    85
    Views
    3,823

    Mate that is one tough truck. I love it! Great...

    Mate that is one tough truck. I love it! Great taste in mods and that's the first time I have seen that body and liked it. You've nailed that build.
  11. That is a good post hog. That really show me...

    That is a good post hog.

    That really show me why my 3300mah 30c 3s is so much less punchy than my 5500mah 35c 3s.
    Just looking at the "c" rating you could think that they would be close with the...
  12. Replies
    67
    Views
    3,521

    Snapped the shaft on my hobbywing 4 pole 4000Kv...

    Snapped the shaft on my hobbywing 4 pole 4000Kv motor running on 3s with 32 pitch gears :(
  13. Replies
    55
    Views
    1,559

    What kind of internet service are you guys...

    What kind of internet service are you guys getting and what part of the world are you in? Those speeds are insane compared to anything we can get here in OZ makes me want to emigrate lol
  14. Replies
    55
    Views
    1,559

    far out! You guys have some fast internet there....

    far out! You guys have some fast internet there. Is that optic fibre cable? Over here in Australia we are lucky to get 5mbps on ADSL2 which drops right off due to congestion at pal tones to below...
  15. Replies
    28
    Views
    1,492

    Since I Jane been racing my 1/10 touring car with...

    Since I Jane been racing my 1/10 touring car with the 21.5t sensored speed passion motor and hobby wing Xtreme stock esc I am a big fan of sensored motors. Its way better to drive than my vxl rustler...
  16. Replies
    16
    Views
    460

    How do you get it to not wheel stand? Is the...

    How do you get it to not wheel stand? Is the front weighed down? Or is ir just wheel spinning so much it won't wheel stand?
  17. Thread: Steel axels.

    by wagnman
    Replies
    12
    Views
    614

    I have mip on my rustler, they seen good so far,...

    I have mip on my rustler, they seen good so far, they do hit the suspension arm on the outer end when the ATM is at full droop but they grind the arm away a but and fit street a couple of runs lol....
  18. Replies
    484
    Views
    24,313

    Snapped the inboard hinge pin of the strc rear...

    Snapped the inboard hinge pin of the strc rear arms that I used to do the "wide mod" on my rustler as well as the bottom mount of my proline shock :-( was all at slow speed as well, clipped a fence...
  19. Replies
    6
    Views
    379

    What's the difference between that and the...

    What's the difference between that and the rustler vxl velineon 3500kv motor? Wouldn't the vxl one be faster as its lower Kv?
  20. Replies
    9
    Views
    436

    My vxl rustler does this sometimes too. Sometimes...

    My vxl rustler does this sometimes too. Sometimes it takes two or three squeezes of the throttle for the motor to kick in after you pull up to a complete stop. once running again its perfect....
  21. Replies
    13
    Views
    737

    Just a question for you guys on these alloy...

    Just a question for you guys on these alloy parts. Hire do you get the screws to stay in there? Loads of Loctite? Its just that the screws bite into the plastic parts so well and the plastic kind of...
  22. Replies
    33
    Views
    2,017

    That looks hot mate, nice one!

    That looks hot mate, nice one!
  23. Thread: Friendly wager

    by wagnman
    Replies
    24
    Views
    959

    How much traxxas parts does a rustler need to...

    How much traxxas parts does a rustler need to have to still be called a rustler?I mean can you really call a rustler with a carbon chassis, after market suspension and Transmission and non traxxas...
  24. Thread: Cleaning!!!

    by wagnman
    Replies
    17
    Views
    570

    I too would like to see what the cleaning routine...

    I too would like to see what the cleaning routine is for many of you experienced guys, I'm back into RC after many years and am looking to building up my kit again and want to keep my new car add...
Results 1 to 24 of 25