Search:

Type: Posts; User: RockchalkJayhawk

Page 1 of 4 1 2 3 4

Search: Search took 0.28 seconds.

  1. Replies
    18
    Views
    400

    wd40 is one of the worst things you could put on...

    wd40 is one of the worst things you could put on a bearing. Temporary fix yes but it will cause your bearing to fail.
  2. Replies
    18
    Views
    400

    ^ agreed if the motor can turn it then check the...

    ^ agreed if the motor can turn it then check the bearing adapter first.
  3. Replies
    15
    Views
    1,010

    Its stock oil

    Its stock oil
  4. Replies
    15
    Views
    1,010

    I would check the whole drive train. I haven't...

    I would check the whole drive train. I haven't run into that problem before. Mine did end up being the diff I believe. I did change wheels too. The rear had slight wear on the hex but were still good.
  5. Replies
    8
    Views
    1,144

    Good point I didn't try that yet. Thanks Nova.

    Good point I didn't try that yet. Thanks Nova.
  6. Replies
    2
    Views
    188

    Ya check the diff too. Just happened on my erbe...

    Ya check the diff too. Just happened on my erbe and the diff looked perfect. Installed one I had on hand and problem solved. Still not sure why that diff did that, it had to wear or missing teeth...
  7. Replies
    8
    Views
    1,144

    I will probably just go ahead and the an external...

    I will probably just go ahead and the an external bec. Thx for the help guys.
  8. Replies
    8
    Views
    1,144

    Glitch buster?

    I recently installed a hitec 7950th and it seemed to need a glitch buster. From a dead stop if you turn the wheels all the way left or right, I would get no throttle response. I installed the...
  9. Replies
    15
    Views
    1,010

    Replaced the rear diff with the new one and all...

    Replaced the rear diff with the new one and all is well. I still have no clue why it had no power to rear wheels. The old diff looked to be in perfect shape.
  10. Replies
    15
    Views
    1,010

    Ya the diff is out right now. Pulled it apart...

    Ya the diff is out right now. Pulled it apart and all gears look fine no wear or missing teeth. The center drive shaft looks fine as far as I can tell. I put the rear part of the shaft back in and...
  11. I made my own plug for the MM in my slash but the...

    I made my own plug for the MM in my slash but the smallest I run in it is 4s.
  12. Replies
    15
    Views
    1,010

    Ya its the stock shaft but it looks fine. I...

    Ya its the stock shaft but it looks fine. I checked the spider gears and the are fine too. Its really got me puzzled now. Does anyone know if it could be something in the tranny?
  13. Replies
    15
    Views
    1,010

    I already have the diff out thinking that was it....

    I already have the diff out thinking that was it. The output grubs were tight and I couldn't see any spin marks on them or the output shafts. The only thing I didn't visually inspect were the...
  14. Replies
    15
    Views
    1,010

    checked the shaft and it seems to be ok. I put...

    checked the shaft and it seems to be ok. I put the back half back in and it turns the slipper just fine both ways by hand.
  15. Replies
    15
    Views
    1,010

    Rear power loss

    Lost power to rear wheels last run I did. My first thought was rear diff. Just took it apart and it looks flawless. Any ideas what else it could be? Wheels look fine although showing some wear.
  16. Replies
    8
    Views
    341

    Are you wanting to stay with the stock motor/esc?...

    Are you wanting to stay with the stock motor/esc? If you want the speed without the worry of over heating I would suggest a different combo. I run the castle MM/2650 and love it. You will need...
  17. You can do speed runs with 6s on the 2650 with no...

    You can do speed runs with 6s on the 2650 with no problems I do it all the time.
  18. Replies
    9
    Views
    1,080

    I hear rc monster is gonna make their hybrid...

    I hear rc monster is gonna make their hybrid diffs again so when the diffs I just ordered go out I will get getting them.
  19. Replies
    21
    Views
    1,244

    Ya I would say it is similar to that. I don't...

    Ya I would say it is similar to that. I don't notice it too much when I am moving and turning, although it will do it some. It won't move at all if I turn the wheels from a dead stop. Might just...
  20. Replies
    21
    Views
    1,244

    Anyone? I did take it out and test it for a...

    Anyone? I did take it out and test it for a minute before I switched the bec to 6v and it didn't do it. It wasn't very long though.
  21. Replies
    63
    Views
    4,766

    Anyone know if they will need shimmed? I don't...

    Anyone know if they will need shimmed? I don't mind paying for something that will stand the test of time but if I am gonna have to replace these even once a year it's not worth it to me. If they...
  22. Replies
    63
    Views
    4,766

    So $200 for a set of diffs? hopefully not quite...

    So $200 for a set of diffs? hopefully not quite that much ouch.
  23. Any progress on the bulks?

    Any progress on the bulks?
  24. Replies
    21
    Views
    1,244

    After running my rig today it was acting up a...

    After running my rig today it was acting up a bit. I set the bec to 6v and it was doing fine at first then I notice from a dead stop if I turn the wheels it won't move forword or reverse. Do I need...
  25. Replies
    21
    Views
    1,244

    Found my trusty manual to my slash and figured...

    Found my trusty manual to my slash and figured out the menu system to reverse it.
Results 1 to 25 of 85
Page 1 of 4 1 2 3 4