Search:

Type: Posts; User: traxxas777

Page 1 of 2 1 2

Search: Search took 0.10 seconds.

  1. Replies
    700
    Views
    16,446

    I basically bought a 4x4 roller and I took my...

    I basically bought a 4x4 roller and I took my tires, motor, esc, receiver, body all off my 2wd pede and put on the 4x4 roller to make it complete.
  2. Replies
    700
    Views
    16,446

    First run of the year after transferring my old...

    First run of the year after transferring my old 2wd pede into 4wd. Fun time of the year to drive because here in mn it's about 45 degrees so the snows melting and it's wet and muddy all around the...
  3. Replies
    53
    Views
    1,679

    get lipos i promise you wont be disappointed. i...

    get lipos i promise you wont be disappointed. i was the same way i only used nihm batteries as i was familiar with them and kinda nervous about lipos. but after two of my lightly used nihms started...
  4. Replies
    1
    Views
    98

    Resolved: i pulled the relatively new and FULLY...

    Resolved: i pulled the relatively new and FULLY CHARGED venom battery pack out and replaced it with the normal 4 AA battery compartment, and tried and it works just fine. Once again another reason...
  5. Replies
    1
    Views
    98

    tqi glitched?

    so i recently bought 2 brand new tqi receivers and a tqi transmitter for my nitro rustler, and electric stampede. i installed 1 receiver in the stampede without an issue and bound it with the...
  6. Thread: tqi help

    by traxxas777
    Replies
    1
    Views
    87

    tqi help

    so I have a stampede with a vxl and my nitro rustler both with tqi receivers that I use with just 1 transmitter. after a few months of not driving either truck I decided bring them out. I ran the...
  7. Replies
    12
    Views
    2,222

    is there anywhere online we can buy parts? the...

    is there anywhere online we can buy parts? the "buy traxxas" page has nothing in stock for the dr1
  8. Replies
    2
    Views
    454

    i have the same kind of problem. not sure why.....

    i have the same kind of problem. not sure why.. but once the heli is in the air it seems to be pretty stable its just when its first taking off, i also had this problem when messing with my brothers...
  9. Thread: the dr-1

    by traxxas777
    Replies
    3
    Views
    386

    after a couple days of owning it and flying it im...

    after a couple days of owning it and flying it im still havin lots of fun, although i figured out the heli is not all that durable. i haven't crashed it too hard or anything but already the hollow...
  10. Thread: the dr-1

    by traxxas777
    Replies
    3
    Views
    386

    the dr-1

    i just got my dr-1 today in the mail today and have already put in a good 8-10mins of flight before the battery died. Ive never flew an rc heli before so it was a bit strange with the controls but...
  11. Replies
    17
    Views
    667

    the steering links im using now are the same...

    the steering links im using now are the same length as my old stock ones were
  12. Replies
    18
    Views
    482

    DO NOT buy mip's. i paid $45 for them and the...

    DO NOT buy mip's. i paid $45 for them and the steel tore apart on both sides. best bet would be stampede 4wd driveshafts. i havent had an issue since i went with thos
  13. Replies
    17
    Views
    667

    stock bearing carrier is longer then the RPM...

    stock bearing carrier is longer then the RPM bearing carrier, with both tie-rod links adjusted as much as they can, the wheels still dont align.
    ...
  14. Replies
    17
    Views
    667

    the package says for elec. stampede. yes its a...

    the package says for elec. stampede. yes its a vxl, i did not buy rpm caster blocks.. maybe thats the problem??. the tie-rod links im using are the traxxas performance ones, they are even slightly...
  15. Replies
    17
    Views
    667

    NEED HELP with front bearing carriers

    okay i just purchased RPM bearing carriers for the front on my 2wd stampede. but with the tie rods screwed on, they will not reach the servo saver... the stock bearing carriers are longer and allow...
  16. Replies
    4
    Views
    185

    driveshaft problem

    is there any decent driveshafts out there for a pede?? the stock ones wont last 5 minutes without breaking either a yoke or stub axle. i tried mip's but both sides cracked, and broke after about 10...
  17. Replies
    11
    Views
    337

    thanks for the help! i re-geared it to stock...

    thanks for the help! i re-geared it to stock gearing and the truck runs fine today without any extreme heat. i think the battery and esc got so hot that it just didnt run right and eventually burst a...
  18. Replies
    11
    Views
    337

    i guess but it wasnt just the battery.. reverse...

    i guess but it wasnt just the battery.. reverse wouldnt work, had only half power and the grinding sound i still havent figured out
  19. Replies
    11
    Views
    337

    yes ive run this battery before without any...

    yes ive run this battery before without any issue, and its a vxl. the first run i noticed the battery was pretty hot too but not as bad as the now melted one. nothing was grinding between the pinion...
  20. Replies
    11
    Views
    337

    problem with my pede.

    so today i stuck a slightly bigger then stock pinion gear in to do some high speed runs, right away i noticed a small grinding sound everytime i would give it throttle. and reverse was not working...
  21. Replies
    4
    Views
    198

    help!! stripped pinion screw????

    ok so today i wanted to try out a different pinion gear on my vxl and when i went to take the pinion off the little screw got stripped out very quickly and now my pinion gear is stuck. how do i get...
  22. Replies
    2
    Views
    231

    traxxas hawk

    so i went to a local pawn shop today and found a traxxas hawk. i ended up buying it and to my surprise it still ran! this little truck is fun! it isnt to fast but for how old it seems to be im...
  23. Replies
    18
    Views
    1,135

    Original old stampede body

    is there somewhere i can find an old xl-1 (msc) stampede body? i love the rainbow style look to them and want one for my stampede that i just rebuilt
  24. Replies
    4
    Views
    441

    yep, its all good i put a new ez start motor in...

    yep, its all good i put a new ez start motor in and it works fine. somethings just jammed in the old one or something.. cant seem to unjam it, or fix it.
  25. Replies
    4
    Views
    441

    yea its not. i took the ez start motor off the...

    yea its not. i took the ez start motor off the truck and its the ez start motor thats locked up. wish there was a simple fix but i bought a new ez start motor anyway
Results 1 to 25 of 48
Page 1 of 2 1 2