Search:

Thanks for the replies.
If you are running Lipo's what are the temps that are OK and not OK?

So am I getting this right? If you had 5 batteries, some fully charged and some at less than full and they got mixed up there is NO WAY that you could tell what their state of readiness is?

This may be a rookie question but can I tell how "charged" a battery is by checking the voltage with a DC voltmeter? Is checking it like this kind of like looking at the fuel meter on a car to see...

What temps are ideal and what are the temps when problems start to occur?

I got the same blinking light combo last night when I put two 1600 mah NiMh batteries in series. What is going on there?

I took mine to the local indoor carpet track last night and used the stock Traxxas TX. I found that this thing definitely goes where you point it and this is not necessarily a good thing. I was...

So....is it OK to run mixed Milli-amp NiMH batteries in series?

I understand completely about matched cells are all about. What I am trying to do is use some odd batteries I have around for just bashing on a track in my yard and then getting a matched set for my...

I could run them in series but what I am looking for is more run time. The track I run on is pretty tight and more power is not needed. This thing has plenty of power for me as it is.

I was wondering if the ESC built in lipo cutoff cares about the voltage of the lipo you use. I have a 11.1 v 3S. Will the ESC really cut it off when it gets to the low voltage point? Would it do...

I have 4 NiMh batteries and none of them match in Milli-amps.
I have a 1100,1200,1400,1600.
The manual says not to mix them I want to run in parallel for longer run times. Are these 4 batteries...

Some Ritt dye would fix the white wouldn't it?
Mofroggy

Is there a replacement steering servo for the Slash that is "stronger" than the Slash Stock steering servo and will fit with no screw hole modifications?
Does anyone know the "specs" on the strength...

The 4mm wrench in the set from Micro-Plastics https://www.micro-tools.com/store/item_detail.aspx?ItemCode=SCR-913-00 worked great. I had to tweak it just a little bit on the outer lips to make it...

OK, what the heck is a torque sleeve's function?

On the 550 12t motor on the Slash there is a steel shroud thing that goes around the motor. The 12T Traxxas logo is on it and it is made out of metal and is a really snug fit. What is this for?

Thanks for the suggestions Bruce. I did find a set at Micro-Tools https://www.micro-tools.com/store/item_detail.aspx?ItemCode=SCR-913-00 that has a 4mm wrench in it for $2.95 plus shipping. I am...

Does anyone know a source for a cheap 4mm open end wrench? I find that the wrench that comes with the Slash is hard to use because if the angle the 4mm opening is and it is too thin and shifts side...

I went to Wal-Mart and bought one of those medium sized glass jars that you keep cookies in for $5.95. I just run the battery charging leads over into the jar, put the lid on, and charge away. I...

Would you please explain why and how and where you put the CA on the outer front tires.
Thanks a lot!

So......you DO want the shaft to rebound??? I always thought that rebound was a sign of trapped air or too much fluid in the shock. You learn something every day.

I am using the ESC that came with the Slash.

I had it hooked up to the stock Traxxas ESC just like you said but when I plugged in the battery and turned on the ESC the ESC blinked green once and then went off. From that state I pushed the bind...

I just got my Slash and I want to set it up with a Spektrum DX 3.0 and a SR3000 RX. I can't figure out where the wires go from the ESC and the steering servo to the SR3000. I have tried the...

I had the same problem with Energizer rechargable batteries. What I did is just put them in so that they line up as best as you than get them, slam the lid on them and put black electrical tap...