Search:

Type: Posts; User: mudrat13

Search: Search took 0.16 seconds.

  1. Replies
    10
    Views
    712

    I agree with Traxxas, I like the REM products....

    I agree with Traxxas, I like the REM products. Definitely the best warranty IMO.
  2. Replies
    9
    Views
    167

    [QUOTE=harry697;5366359]No offense to you, it's...

    [QUOTE=harry697;5366359]No offense to you, it's just that this subject has been brought up quite a few times here. Oil level or viscosity has no effect on ride height. If anything, the oil will cause...
  3. Replies
    9
    Views
    167

    I believe in the manual it says for the control...

    I believe in the manual it says for the control arms to be just above parallel to the ground. you might check your shock oil level, or check for suspension binding. It doesn't appear that you have...
  4. Replies
    6
    Views
    231

    I boil mine for 12 minutes and then pull it off...

    I boil mine for 12 minutes and then pull it off bare handed, since there isnt much heat transfer to the rubber.
  5. Replies
    4
    Views
    103

    After further investigation, traxxas recommends...

    After further investigation, traxxas recommends no more than 9 cells at 10.8 volts, and 3s lipo at 11.1. So i guess it cant be done
  6. Replies
    4
    Views
    103

    7 cells in series

    I have been teasing the idea of hooking up 2 of my 7 cell NIMHs in series on my Rusty. I have numerous 7 cells and i dont know if the VXL ESC will handle it. Thanks for any input!
  7. Replies
    9
    Views
    1,245

    I run the tranny case from REM, its completely...

    I run the tranny case from REM, its completely aluminum and is the only case I have had to stand up to my abusive bashing. It does add some rear weight, but I'm not a racer.
  8. Replies
    9
    Views
    204

    48 pitch for your gearing

    48 pitch for your gearing
  9. Replies
    10
    Views
    380

    If you decide to go lipo, you will need a charger...

    If you decide to go lipo, you will need a charger that is lipo compatible, and a charging bag. For your money a 7 or 8 cell NIMH will do you jjust fine.
  10. Thread: wing/spoiler?

    by mudrat13
    Replies
    6
    Views
    287

    I like the wing, not sure how it will hold up to...

    I like the wing, not sure how it will hold up to my kind of bashing tho... broke the rear shock tower in pieces yesterday. Time to calll REM again!
  11. Thread: wing/spoiler?

    by mudrat13
    Replies
    6
    Views
    287

    Looks nice. I wasnt sure to either mount it to...

    Looks nice. I wasnt sure to either mount it to the rear shock tower or the tranny. I like how your mounts look like a package unit. I was thinking ofusing the upper wing mount and two pieces of...
  12. Replies
    17
    Views
    588

    it isnt just the speed, its hard acceleration,...

    it isnt just the speed, its hard acceleration, and braking. when i run at my local track my temps are nearly 30 cooler than bashing around at home and the donuts. in my opinion i would say the 23...
  13. Thread: wing/spoiler?

    by mudrat13
    Replies
    6
    Views
    287

    wing/spoiler?

    for all you rc-ers, i have probably an easy question. does the e-revo spoiler fit the rusty? and if so, does it fit the motor guard/ wheelie bar mount?
  14. Replies
    1
    Views
    117

    I switched to an alum tranny not long ago and it...

    I switched to an alum tranny not long ago and it is relatively simple. You do need grease though, i use super lube. As long as it is synthetic and will hold up to high heat you should be ok.
  15. by "slicking" i mean to where the paddles get so...

    by "slicking" i mean to where the paddles get so clogged with snow, mud, wet sand, etc. to where they are almost "slick" looking and have no traction whatsoever. i have find that with the sandpaws i...
  16. traxxs part number 5116 5x11x4 bearings

    traxxs part number 5116 5x11x4 bearings
  17. Replies
    2
    Views
    72

    rear coverage?

    i have been looking for some kind of rear bumper for my rusty. i know the slash rear bumper fits without a hitch, but it looks like a monstrosity hanging off of the rear. i have had my eye on the rpm...
  18. i would have to say the PL sandpaw is more adept...

    i would have to say the PL sandpaw is more adept to not "slicking" over with the stepped scoops. larger tires does mean more heat on a surface with traction, however if you are wanting to run them...
  19. http://www2.gpmd.com/imagem/s/mstrc0059.jpg

    http://www2.gpmd.com/imagem/s/mstrc0059.jpg
  20. looks to me as you need the bearings for those...

    looks to me as you need the bearings for those hubs, the difference in length for the axle is of no issue to the geometry of the suspension
Results 1 to 20 of 20