Search:

Type: Posts; User: ling427ttvette

Page 1 of 17 1 2 3 4

Search: Search took 0.07 seconds.

  1. Replies
    13
    Views
    321

    Ok I see where you are going with it now, I took...

    Ok I see where you are going with it now, I took it as you were meaning to run it as soft as possible.

    I agree that letting it be soft enough to reach full compression but not to soft as to make...
  2. Replies
    13
    Views
    321

    Bottoming out can have many negative effects. The...

    Bottoming out can have many negative effects. The chassis isn't going to like being bounced off the ground for one. The shock tower mounts won't like the extra force being put on them when the...
  3. Just a wheel they came pre mounted on from...

    Just a wheel they came pre mounted on from Proline. They came pre mounted and glued.. Only way to go IMO.
  4. http://img.tapatalk.com/d/14/04/22/6etuha7y.jpg ...

    http://img.tapatalk.com/d/14/04/22/6etuha7y.jpg

    Got my trenchers and steering parts in! Need to order some carriers and some wings still. After that will be the aluminum pushrods and then the...
  5. Replies
    484
    Views
    22,364

    Absolutely nothing. Hard to break stuff in the...

    Absolutely nothing. Hard to break stuff in the middle of a build lol. Got parts coming and it should be up and running soon.
  6. Replies
    18
    Views
    350

    But then you need to think how that heat might...

    But then you need to think how that heat might affect the other parts that are touching what you are heating up.
  7. Replies
    18
    Views
    350

    I don't thread lock anything on my RC's either....

    I don't thread lock anything on my RC's either. But I'm with Martin, if it's something you're going to be taking apart again.. Blue loctite and very little goes a long ways. I have seen red loctite...
  8. Replies
    18
    Views
    350

    Is red thread lock really needed? Would the blue...

    Is red thread lock really needed? Would the blue get it by? Red thread lock is some pretty tough stuff.
  9. Well, been bashing around a bit and found out...

    Well, been bashing around a bit and found out that basically all 8 tires I have are junk. The glue will not hold. I've also started the build on the other chassis.

    To start with I ordered me some...
  10. Replies
    4
    Views
    216

    Why would you lock the front and leave the rear...

    Why would you lock the front and leave the rear limited slip? I would make it the other way around myself. Locked rear for traction, and a limited slip front so I could still turn easy. Looks nice...
  11. Replies
    17
    Views
    270

    Traxxas Slash 2wd converted to VXL, Emaxx 3905...

    Traxxas Slash 2wd converted to VXL, Emaxx 3905 and 3906, and two mini Revo VXL's. Only current Traxxas I own is a MERV. I regret getting rid of the others. But I wanted something different and...
  12. Replies
    3
    Views
    498

    $350s a bit much considering it's not a PE and...

    $350s a bit much considering it's not a PE and comes with no radio system IMO.
  13. Replies
    16
    Views
    634

    \ No interest at all in the E-Maxx;s?

    \

    No interest at all in the E-Maxx;s?
  14. Replies
    16
    Views
    634

    Any interest in 3905 and 3906? The 3906 is...

    Any interest in 3905 and 3906? The 3906 is completely tore apart right now, the 3905 has a broken drive shaft. Was in the process of taking the steel shafts from the 6 to put in the 5. The 3906 needs...
  15. Replies
    60
    Views
    3,629

    Very nice. :) You have just given me the BL...

    Very nice. :) You have just given me the BL system that I want.

    Did you have to order the bullet connectors separately for the ESC? If so mind showing me where you got them?
  16. You could run a V-Twin setup.. two VXL motors and...

    You could run a V-Twin setup.. two VXL motors and two ESC's, with the un-slow harness I think it's called and the special receiver cable it will work. Stay waterproof and go brushless!

    This is...
  17. Replies
    6
    Views
    1,055

    Take a few more pain killers, and call them back...

    Take a few more pain killers, and call them back up.. tell them you need another one for me. :)
  18. I hear ya there, I'll take this over that any...

    I hear ya there, I'll take this over that any day. Now, I can't decided if I want to sell off all the pieces from the 6 and use that to upgrade the 3905.. or if I want to slowly upgrade it and build...
  19. I hope you're prepared for this then, because it...

    I hope you're prepared for this then, because it will probably happen. You should get a little luckier if you're pulling screws out of plastic pieces, instead of aluminum like I was. I was going to...
  20. Wow, what a HORRIBLE day of wrenching on the 3906, with pics!

    Let me start off with saying, who ever thought phillips head screws was a good idea is about to get a major smack in the face from me if I find them.

    The other day I broke a driveshaft on the...
  21. Replies
    6
    Views
    996

    Eh.. how do I know if its got the wide maxx...

    Eh.. how do I know if its got the wide maxx suspension?

    And that's what I was thinking about doing, was putting the 3905 shafts in there, and just getting the replacement parts for the broken one...
  22. Replies
    6
    Views
    996

    So the two center shafts aren't the same length,...

    So the two center shafts aren't the same length, I kind of figured that.. but the shafts going from the diffs to the hubs are the same, right? I don't see why they would be, both trucks have the same...
  23. Replies
    6
    Views
    996

    Driveshaft questions

    I've got a 3906 and a 3905 as seen in my sig..

    Was out running the 5 a few minutes ago, was reversing and hit forward and caught a little traction.. snapped the diff output and bent the u-joint...
  24. Replies
    10
    Views
    1,271

    This is the exact reason I am considering doing...

    This is the exact reason I am considering doing the V-Twin mod.
  25. Replies
    27
    Views
    1,906

    I got my 3905 and 3906 at the same time and I ran...

    I got my 3905 and 3906 at the same time and I ran the stock 14.4 ESC and Titans from the 3906 in the 3905 until I got the EVX2 and newer Titans for the 3905.. and that alone was a huge difference...
Results 1 to 25 of 407
Page 1 of 17 1 2 3 4