Search:

Type: Posts; User: olds97_lss

Page 1 of 20 1 2 3 4

Search: Search took 0.19 seconds.

  1. Replies
    13
    Views
    1,074

    Huh... I kind of made something like that a long...

    Huh... I kind of made something like that a long time ago to try in my aftershock. Couldn't get it to stay lined up though and gave up on it. Looks like those have recesses in the disk for teh plate...
  2. Replies
    13
    Views
    1,074

    Whats the VDP kit? I think I'm running blue...

    Whats the VDP kit?

    I think I'm running blue with 60 weight on the rear, P2's and pushrods mounted on the inside holes of RPM arms. The big block weighs it down a bit though. I'm afraid running any...
  3. Replies
    13
    Views
    1,074

    What's the m2c plate made out of? I'd still want...

    What's the m2c plate made out of? I'd still want a skid anyway. Would rather wear out the skid than wear out my arms/hing pin area. It is a good safety though to avoid losing the pins.
  4. Replies
    13
    Views
    1,074

    Tired of rear skidplate wear...

    Well, I've been through about 4 stock skids and 2 alloy skids (1 integy and 1 GH), then I found the impact RC skid wear plates and ran those a bit. Problem was is that I'd need a new one every...
  5. Replies
    7
    Views
    922

    Yep, uses a thick o-ring and nylon shim. Seemed...

    Yep, uses a thick o-ring and nylon shim. Seemed to work just fine, was a bit sketchy on my OS18, but I got that to work as well. I think I just cut the ring off the normal header gasket, then used...
  6. Replies
    7
    Views
    2,930

    I just did something like the other guys did and...

    I just did something like the other guys did and used a turnbuckle to give it some support. I'm using a losi aftershock/lst turnbuckle and bolted it to the top bolt on one of the shocks and the...
  7. Replies
    12
    Views
    1,136

    Was just saying it's fairly easy and direct to...

    Was just saying it's fairly easy and direct to take out the two cradle bolts. Only takes a few seconds to reset the gear mesh.
  8. Replies
    56
    Views
    7,008

    Crappy quality video, but this is my aftershock...

    Crappy quality video, but this is my aftershock with the LRP in it shortly after break-in:
    http://www.youtube.com/watch?v=ex7OCovM5iI
  9. Replies
    55
    Views
    2,964

    Your camera man is insane. Didn't even flinch...

    Your camera man is insane. Didn't even flinch when that thing went between his legs!
  10. Replies
    12
    Views
    1,136

    Huh... I always found the easiest was to take the...

    Huh... I always found the easiest was to take the two long bolts out of the cradle. One under the chassis near the center of the truck and one above the chassis. I think I used to have to take the...
  11. That's what I run on my savage, but savage axles...

    That's what I run on my savage, but savage axles are bigger where the hex fits which would create a wobbly wheel after a short time. Are the e-savage axles smaller than the nitro savage? If so,...
  12. Replies
    56
    Views
    7,008

    Yes. Has decent RPM's as well. I run one in my...

    Yes. Has decent RPM's as well. I run one in my savage and one in my aftershock. Thirsty engine, but a fairly strong and long lasting engine. I probably have about 5 gallons through each of mine and...
  13. Replies
    56
    Views
    7,008

    What engine mount? Is it the new era leaner all...

    What engine mount? Is it the new era leaner all purpose BB mount? At full compression, I have about 1/2" between the arm and the starter housing.

    What rockers/pushrods are you running? I'm running...
  14. Replies
    56
    Views
    7,008

    You "had to" buy the horizon arm? I had a OS21RG...

    You "had to" buy the horizon arm? I had a OS21RG back in the day in my revo with the NE BB leaner kit and it didn't get that close to the arm under full compression. That thing had one of the largest...
  15. Replies
    56
    Views
    7,008

    Yeah... on the plus side, I have a nice fantom...

    Yeah... on the plus side, I have a nice fantom revo pipe and a almost new trinity pipe that I got both of cheaply on ebay... so if I ever drop down to a 3.3 or dynamite 19... I'll have a few decent...
  16. Replies
    14
    Views
    1,475

    If you find a longer header, you can sling the...

    If you find a longer header, you can sling the pipe down lower to be almost as low as the chassis deck. With your body up a couple holes on the mounts, you shouldn't have to cut much.

    I started a...
  17. Replies
    2
    Views
    1,289

    Shouldn't be a problem. I have a set on RPM rims:...

    Shouldn't be a problem. I have a set on RPM rims:
    http://home.comcast.net/~98gmarquee/pics/revo/2010-0618-RevoNERollBarWingBBFantomEngineSide.jpg

    They are also 3.2" at the bead:...
  18. Replies
    9
    Views
    1,235

    Just curious, what tooth spur/cb are you running?...

    Just curious, what tooth spur/cb are you running?

    I'm sure I can find this info somewhere else, but what's the difference between wide, close and standard trans gearing? Mine started as a slayer,...
  19. Replies
    20
    Views
    1,268

    I really like what you did there. I'd add a hood...

    I really like what you did there. I'd add a hood out of lexan or something though to make it look more complete. Looks great though!
  20. Replies
    56
    Views
    7,008

    Well, I went back to a side pipe anyway. I want...

    Well, I went back to a side pipe anyway. I want something that's durable and the rear pipe is tough to make that way. Besides, it kind of tuned poorly as well. So, with a hack saw and some...
  21. My hardware store only had 5mm nuts, nothing else...

    My hardware store only had 5mm nuts, nothing else that was 5mm. I may end up getting those brass inserts later if these show signs of wear.
  22. Would assume you could do the same with those...

    Would assume you could do the same with those inserts, except it would have been way easier to mill down brass than it was to mill down steel.

    I threaded 6-8 nuts on a 5mm bolt, put the threaded...
  23. Replies
    56
    Views
    7,008

    Well, I noticed that the heat had a negative...

    Well, I noticed that the heat had a negative affect on the JB weld, so I'm trying a brass fitting like you, but I'm using something called "PC Fahrenheit". Good up to 500F. I bought some new jb-weld...
  24. Replies
    7
    Views
    2,930

    Does it actually go into the bulkhead on the...

    Does it actually go into the bulkhead on the e-revo? On the nitro revo, I'm pretty sure it's just threading into the bottom part of the body mount and nothing else, so it's only 1/4" at most of...
  25. Replies
    56
    Views
    7,008

    I pealed my copper fitting off and apparently, JB...

    I pealed my copper fitting off and apparently, JB weld does not adhere to copper at all. Was a pain getting it off the pipe, but not a single piece of JB stuck to the copper. How well does it adhere...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4