Search:

Type: Posts; User: tyler2474

Search: Search took 0.04 seconds.

  1. Replies
    87
    Views
    12,688

    In the info on his Youtube video, he says he...

    In the info on his Youtube video, he says he paused the timer as he checked the speed on the GPS.
  2. Replies
    87
    Views
    12,688

    I'm not totally convinced that he faked it by...

    I'm not totally convinced that he faked it by your reasoning. The Garmin Forerunner 101 has an Auto Pause feature, which pauses the timer when the GPS drops below a certain speed. This could be the...
  3. Replies
    4
    Views
    285

    I took it apart, and, as you said, the center...

    I took it apart, and, as you said, the center driveshaft itself was bent. Thanks for the help.
  4. Replies
    4
    Views
    285

    Yes. All bearings are in place.

    Yes. All bearings are in place.
  5. Replies
    4
    Views
    285

    Center Driveshaft Wobble

    I built my XO-1 from all new parts bought from eBay, but, once it was all together, I could see that the center driveshaft had a slight wobble. I could feel by turning the driveshaft that there were...
  6. Replies
    31
    Views
    1,524

    Thanks for all of the suggestions guys! I have...

    Thanks for all of the suggestions guys! I have yet to try putting the plastic suspension pin holders on the Integy case, but I will hopefully try that soon.
  7. Replies
    2
    Views
    254

    Thank you.

    Thank you.
  8. Replies
    2
    Views
    254

    Quick Question About the Motor Mount

    Are there two bearings that go into the motor mount where the cush drive goes through it, or only one?
  9. You might also have some suspension binding like...

    You might also have some suspension binding like bent suspension pins, bad balls in the rod ends, or bent shock shafts. The shock would still return to its position even without shock oil because it...
  10. Replies
    8
    Views
    217

    Also try some new stub axle carriers if the...

    Also try some new stub axle carriers if the bearings fit loose inside of the carriers (part #3652).
  11. Thread: less heat

    by tyler2474
    Replies
    36
    Views
    481

    All the gearing came right off of Castle's...

    All the gearing came right off of Castle's gearing chart and they are for the Bandit. Here is the chart: http://www.castlecreations.com/support/documents/gearing_chart.pdf
  12. Thread: less heat

    by tyler2474
    Replies
    36
    Views
    481

    It seems something is wrong with your motor or...

    It seems something is wrong with your motor or something in the drive line is not right, causing the motor to work harder, as Greatscott said.
  13. Thread: less heat

    by tyler2474
    Replies
    36
    Views
    481

    Castle recommends running 2S LiPo or 6 - 7 cell...

    Castle recommends running 2S LiPo or 6 - 7 cell NiMH with a 12 - 16 tooth pinion and a 90 tooth spur for the 1406 series 5700 kv motor, and a 12 - 14 tooth pinion and a 90 tooth spur for the cm36...
  14. Thread: less heat

    by tyler2474
    Replies
    36
    Views
    481

    What kv motor are you running?

    What kv motor are you running?
  15. Replies
    31
    Views
    1,524

    I had just bought all new suspension pins before...

    I had just bought all new suspension pins before installing the case. Also the suspension pins did not go through the holes without using a hex driver and oil to push them in (no a arms attached...
  16. Replies
    31
    Views
    1,524

    Thanks for all the help! I think I might try...

    Thanks for all the help! I think I might try Zoomad's idea with using the arm mounts off of the stock plastic case. If that doesn't work, I'll try the Hot Racing case. Also, it said on Hot...
  17. Replies
    31
    Views
    1,524

    Integy Gearbox on Rustler Mishap

    So I purchased the Integy gearbox (Integy part # T7983) to put on my Rustler so that I could run the 2200 kv Castle Creations motor. The suspension pin holders on the sides of the gearbox were too...
  18. When connected in a series or parallel...

    When connected in a series or parallel connection, batteries should be identical. Using batteries with different numbers of cells in these types of connections is not a good idea.
  19. Replies
    3
    Views
    157

    Thanks for the answers! Would it be beneficial...

    Thanks for the answers!

    Would it be beneficial to go with metal-sealed ball bearings (would they last longer without having any trouble), or is it better to have bearings that are serviceable?
  20. Replies
    3
    Views
    157

    General Maintenance Questions

    I've had my Rustler VXL a couple years now and just cleaned the bearings (probably should have done it much sooner, but actually had only a couple with a little rust in them). I cleaned them all,...
Results 1 to 20 of 20