Search:

Type: Posts; User: josh12845

Search: Search took 0.24 seconds.

  1. Replies
    17
    Views
    2,657

    Easiest way is to remove the front end by...

    Easiest way is to remove the front end by removing the 4 or 6 screws(cant remember which) on the bottom of the chassis. The front then slides out making it easier to center your steering.
  2. Thread: Jato wheels

    by josh12845
    Replies
    3
    Views
    606

    not that i have seen. due to the fact the front...

    not that i have seen. due to the fact the front wheels have 2 barings and a spacer.
  3. Replies
    4
    Views
    372

    has it been broken in? has it been tuned?...

    has it been broken in? has it been tuned? acceleration could be from lsn needing leaned out. tighten the screw on the spur gear in a little. looks way out compared to mine. might have too much slip....
  4. Replies
    7
    Views
    526

    May sound dumb, but if your cover the pipe hole...

    May sound dumb, but if your cover the pipe hole while trying to crank, it will pull the fuel to the carb, also now as "priming". Sometime when first starting, mine wont pull on its own, I have to...
  5. Replies
    1
    Views
    496

    Fronts- Definetly go ribbed. I run dirt and the...

    Fronts- Definetly go ribbed. I run dirt and the anacondas sucked, and all the terrain tires didnt do great. Ribbed was awesome. For the rear- idk maybe a paddle to run in the sand pits.
  6. Replies
    9
    Views
    660

    if it seems like its turning the engine over and...

    if it seems like its turning the engine over and then stops, but the motor on the easy start keeps spinning, then its the one way bearing in the easy start. about a $20 fix.
  7. Replies
    2
    Views
    1,441

    Thanks for the quick reply. I've never noticed...

    Thanks for the quick reply. I've never noticed that set screw and i've had it apart probably 20 times. But your absolutely right. That fixed it. Thanks again.
  8. Replies
    2
    Views
    1,441

    Trx Carb issues

    Long story short. old carb cracked. Bought a new one. But the horn for the throttle servo is upside down from the old one and it binds my servo a little. Can this be adjusted on the carb? For...
  9. Replies
    5
    Views
    643

    Look really close around the bottom of the carb...

    Look really close around the bottom of the carb and engine. if you see a little bit of nitro, then its prob the carb o ring or a hairline crack in the carb. Obviously remove to inspect. Hope this...
  10. Replies
    8
    Views
    539

    Thanks. Ill look again this weekend. It didnt...

    Thanks. Ill look again this weekend. It didnt look twisted to me, but maybe i need to remove all the parts to check it out.
  11. Replies
    8
    Views
    539

    my new body is the same exact way, so i know the...

    my new body is the same exact way, so i know the body is beat up but thats not it
  12. Replies
    8
    Views
    539

    http://i1150.photobucket.com/albums/o620/josh12845...

    http://i1150.photobucket.com/albums/o620/josh12845/019_zpsc9919a04.jpg
    heres one
    http://i1150.photobucket.com/albums/o620/josh12845/020_zps1bc3ae1a.jpg
    heres another
  13. Replies
    8
    Views
    539

    sorry removed

    sorry removed
  14. Replies
    8
    Views
    539

    The chassis appears to be level. I removed the...

    The chassis appears to be level. I removed the towers and put them back on. Still nothing.
  15. Replies
    8
    Views
    539

    Stock bodies dont fit!!!!

    I have a Jato 3.3. The stock body doesnt fit on the body mount studs. If you place it on the front body mount pegs, the rear holes in the body are about 1/4 inch past the mounting studs. Bought a new...
Results 1 to 15 of 15