Search:

Type: Posts; User: SacramentoTraxxasLover

Page 1 of 3 1 2 3

Search: Search took 0.10 seconds.

  1. Replies
    10
    Views
    387

    i had the same problem when i first got my...

    i had the same problem when i first got my summit, and ended up striping the gears in one. Thats when i went with the hitech 7990th and have been very pleased. Many would say that its overkill but i...
  2. Replies
    29
    Views
    1,426

    I ended up buying a link card, but at first i...

    I ended up buying a link card, but at first i asked the guy at the hobby shop if he could set it for me, then i took it home and hooked it up and used it... point being is that if all you have is a...
  3. Replies
    29
    Views
    1,426

    BTW... when i had my 4ws setup on my summit i was...

    BTW... when i had my 4ws setup on my summit i was running two (one for front one for rear) hi-tech 7990 off of my tekin's internal bec(i think i also breifly ran the evx2 with that 4ws setup not sure...
  4. Replies
    29
    Views
    1,426

    your going to have to look up the amp rating on...

    your going to have to look up the amp rating on the servos and decide. if they are under 5amp each or 10amp combined yeah if not then your better off with the 20amp model. the 20amp has two out puts,...
  5. scaniris, you are doing a great job and your...

    scaniris, you are doing a great job and your english is fine, you have an accent but so what! as for the videos i think it will end up being a huge contribution as i have bought many parts and...
  6. Replies
    29
    Views
    1,426

    a exteral bec allows you to adjust the power to a...

    a exteral bec allows you to adjust the power to a servo and provides more amps to power them. the part you might need is the higher amp rating because some of those high torque servos drain a lot of...
  7. Replies
    10
    Views
    1,048

    yeah get some heat in it with a heat gun/hair...

    yeah get some heat in it with a heat gun/hair dryer, also once you get it started, i hope your breaking it in? put something around the head like aluminum tape/foil wrap or sock/paper towel and keep...
  8. Replies
    18
    Views
    1,796

    As far as running a single servo setup, its great...

    As far as running a single servo setup, its great but dont just pull one and leave the other (single) servo stock! IMO metal gears are a must and I wouldn't go with less than 300in/oz of torque. Four...
  9. Replies
    18
    Views
    1,796

    as far as using a big block on a revo, i have...

    as far as using a big block on a revo, i have gotten away with using plastic gears with a forward only conversion. I have heard of metal geared trans, but havent had to upgrade to one (although i did...
  10. Replies
    11
    Views
    2,514

    I'm running the moab's on rocksters and hovew no...

    I'm running the moab's on rocksters and hovew no prob on the rocks and i have also opened up the tekin r8 on 4s with no problems they also grip anywhere, one thing i did to them was swap the stock...
  11. Replies
    9
    Views
    1,435

    have you changed the glow pug? sometimes i find...

    have you changed the glow pug? sometimes i find myself pulling my hair out for hours only to remember to try that and boom im up and running again! after that i would eliminate the easy stuff clean...
  12. Replies
    5
    Views
    816

    all i know about is shoe goo and for sealing...

    all i know about is shoe goo and for sealing backplates and carbs orange permatex gasket maker stuff
  13. Replies
    17
    Views
    608

    it is also my understanding that the engine does...

    it is also my understanding that the engine does not have to be exactly at bdc. simply turn the flywheel by hand until it goes PAST the top of its stroke (the hardest part) and spins freely (not in...
  14. Replies
    17
    Views
    608

    this is especially true when the engine is being...

    this is especially true when the engine is being broken in because, as metal has heat cycle put through it it get harder so while the engine is new the metal is not only its biggest (not shaven to...
  15. Replies
    17
    Views
    608

    the reason its good, as i understand and correct...

    the reason its good, as i understand and correct me if im wrong, the sleeve that the piston is surrounded by is narrower up top and wider at the bottom. when things are hot (piston and sleeve) they...
  16. Replies
    18
    Views
    1,796

    definitely upgrade the servo's! I lost a set of...

    definitely upgrade the servo's! I lost a set of a-arms from a weak throttle/brake servo that went out at full throttle :( . Get a good metal geared steering servo (with a alum. horn) for the steering...
  17. Replies
    19
    Views
    2,042

    If you haven't already check out the Summit...

    If you haven't already check out the Summit forum, first take a look at the F.A.Q.S then glance through the posts. They have allot of info about all kinds of things like tires, rims and all sorts of...
  18. Replies
    14
    Views
    2,727

    I have both nitro (revo) and electric (summit)...

    I have both nitro (revo) and electric (summit) also and do have the convenience of going to the hobby shop when all else fails (don't need to now as much and could manage without them but I do...
  19. Replies
    9
    Views
    1,435

    from the info you provided it sounds like its...

    from the info you provided it sounds like its your tune... is there smoke coming out the pipe? how thick? whats the temp of the motor sounds like its a little ritch but i wouldnt lean it out unless i...
  20. Replies
    17
    Views
    608

    when I got my first nitro (a Revo) I made the...

    when I got my first nitro (a Revo) I made the mistake that g mentioned and thought that as soon as I completed the steps like the DVD says to I can go bash at full throttle like the DVD implies. that...
  21. Replies
    13
    Views
    1,741

    i havent tried the setup gordon is refering to...

    i havent tried the setup gordon is refering to but i did go the big block route a couple years ago and used the new era mount with a rear exiting exhaust pipe made by tinity, used a 3 pad clutch...
  22. Replies
    10
    Views
    268

    as far as when you know when to stop running them...

    as far as when you know when to stop running them if your going to spend more that $100 on lipos at least spend $20 or so on a lvc (Low voltage cutoff) definetlly on the bec side if not both lipos....
  23. IMO, the transmission and other sealed parts are...

    IMO, the transmission and other sealed parts are best lubed with grease (like the kind you use on automotive wheel bearings) as they are closed off from contact with the outside world. also as far as...
  24. Replies
    9
    Views
    419

    the way i have mine set up is - all the way...

    the way i have mine set up is - all the way forward is high unlocked (high + locked = broken parts) - first click (middle) is low unlocked and all the way towards the trigger (third click) is low...
  25. Replies
    24
    Views
    1,151

    the difference in torque is not even comparable...

    the difference in torque is not even comparable the tekin is sooooo better in every aspect (except not being waterproof from the factory) trust me (and others) if you have the money you WILL be very...
Results 1 to 25 of 59
Page 1 of 3 1 2 3