Search:

Type: Posts; User: chops1sc

Page 1 of 20 1 2 3 4

Search: Search took 0.15 seconds.

  1. Sticky: Here is a clip of my daughter and me driving her...

    Here is a clip of my daughter and me driving her Stampede in the snow!


    https://www.youtube.com/watch?v=2MqsobCXqQc
  2. Replies
    4
    Views
    192

    Yes, this is very common with the stock rear...

    Yes, this is very common with the stock rear setup. RPM offers a tru-trac rear arm and carrier that eliminates the tie rods on the back. Probably one of the best innovations for the Revo IMO!
  3. Thread: Bearings

    by chops1sc
    Replies
    10
    Views
    181

    I work in the bearing industry. The purpose of...

    I work in the bearing industry. The purpose of seals on a bearing is to keep grease/oil in the bearing. Shields are there to keep debris out. If you put oil on a shielded bearing it will not stay in...
  4. Replies
    10
    Views
    170

    Good to know you got spares. But push come to...

    Good to know you got spares. But push come to shove you could use the larger half until you got the replacement. I had the same issue happen during a race with my slash.
  5. Replies
    5
    Views
    192

    Try richening (is this a word? Lol) the HS needle...

    Try richening (is this a word? Lol) the HS needle and make a few passes while monitoring the temps. And make sure you have plenty air flow.
  6. Replies
    3
    Views
    64

    You can also plasti-dip the servo. Once it dries...

    You can also plasti-dip the servo. Once it dries just cut around the output shaft. Another option to add to the grease/silicone is out a small o-rnig around the output shaft. the servo horn will make...
  7. Thread: Revo problem

    by chops1sc
    Replies
    9
    Views
    308

    Make sure the wheel nuts aren't too tight. This...

    Make sure the wheel nuts aren't too tight. This will also cause the no-turn of the wheels.
  8. Replies
    8
    Views
    206

    +1 for Tekno! I installed mine back when I used...

    +1 for Tekno! I installed mine back when I used to race and it definitely helped! I also bash and it helps rollovers, although it can only to so much. It all depends on how hard you run your truck.
  9. What did you do to you Rusty/Bandit today?

    I get my screws from hexcrews.com
    http://www.hexcrews.com/m3x80-socket-cap-screw.aspx
  10. Thread: Wider Wheels

    by chops1sc
    Replies
    5
    Views
    170

    Wider Wheels

    I use RPM Revolver wheels. They even offer a deep offset for an even wider stance.
    http://i159.photobucket.com/albums/t142/chops1sc/Revo/DSC00911.jpg
  11. Replies
    16
    Views
    285

    Combo or not, you aren't going to find many BL...

    Combo or not, you aren't going to find many BL motors (that are decent quality) for less than $100. You can get the combo and sell the ESC.
  12. Try Photobucket. I have used it for years! As...

    Try Photobucket. I have used it for years!

    As far as my Rustler goes, I finished installing my new sealed diff and slipper, programmed my new Sidewinder to my DX3R and realized that JConcepts...
  13. Replies
    16
    Views
    285

    The new Sidewinder 3 combos start at 99.99 at...

    The new Sidewinder 3 combos start at 99.99 at Tower. I got my 4600KV combo last week.
  14. Replies
    145
    Views
    7,799

    Just ordered mine for my Rustler!! Thanks for the...

    Just ordered mine for my Rustler!! Thanks for the great write-up!
  15. Replies
    16
    Views
    354

    Yeah, I noticed it was hexed while taking the...

    Yeah, I noticed it was hexed while taking the tranny apart. I found a cpl places that sell the all the stuff needed all in one bundle.
    My next list is starting to take shape:
    RPM bumper
    RPM arms...
  16. Replies
    16
    Views
    354

    Thanks guys, I did install a Spektrum high torque...

    Thanks guys, I did install a Spektrum high torque servo I had laying around and it seems much better. It does have bearings all the way around and a closer look at the carriers revealed they are RPM....
  17. Replies
    16
    Views
    354

    Got my goodies today!! ...

    Got my goodies today!!

    http://i159.photobucket.com/albums/t142/chops1sc/6B27946D-6AB4-499D-8977-EAE560365D23.jpg...
  18. Replies
    16
    Views
    354

    I'm not much for having shelf queens. I have too...

    I'm not much for having shelf queens. I have too much fun enjoying my RCs and breaking things, LOL! And I'm pretty good at that! Good thing parts are cheap....


    Sent from my iPhone using Tapatalk
  19. Replies
    16
    Views
    354

    Yeah I will definitely put the slipper back on. I...

    Yeah I will definitely put the slipper back on. I will also put some new axles and eventually all new arms and knuckles.

    I was driving it around Saturday and realized none of the tires had any...
  20. Replies
    16
    Views
    354

    My "old" Rustler

    I'm not worried about parts. I was just curious to know the age of it. I looked in the tranny and it has all metal gears so it was either upgraded or it's a later model.

    My plans include a 4600KV...
  21. Replies
    16
    Views
    354

    My "old" Rustler

    I recently got this old Rustler from a friend (who got it from someone else and so on) and I am trying to figure out what model it is. It has aftermarket electronics except for a Traxxas #2018 servo....
  22. Personally, I would send them off AND buy new...

    Personally, I would send them off AND buy new arms. If they replace them you will have an extra set for the next time your friend wants to drive. If they don't replace them you will need a new set...
  23. Replies
    19
    Views
    1,006

    My personal preference for the pinch test is 1-2...

    My personal preference for the pinch test is 1-2 seconds. However, I am running a OS .18TM.

    Maybe reset both needles to factory settings and start over? Also how tight or loose is your slipper?
  24. Replies
    13
    Views
    730

    PM sent....

    PM sent....
  25. Replies
    13
    Views
    730

    Lower price bumper!

    Lower price bumper!
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4