Search:

Type: Posts; User: Adam2104

Page 1 of 6 1 2 3 4

Search: Search took 0.04 seconds.

  1. Replies
    5
    Views
    992

    Titan died, KD Revolver 650s?

    Finally one of my Titan's died. I figured it was coming as the truck has been quite slow lately. I'm thinking of putting the KD Revolver 650s in as a replacement. Has anyone upgraded to these? How...
  2. Replies
    2
    Views
    919

    It showed up today. I must say, its a very nice...

    It showed up today. I must say, its a very nice radio. I totally dig the end point adjustment. I was able to get the 2-speed micro-servo to finally be dead quiet in both 1st and 2nd gear, something I...
  3. Replies
    5
    Views
    323

    The FASST should work with analog servos, you...

    The FASST should work with analog servos, you should set the radio to the PPM mode.
  4. Replies
    2
    Views
    919

    Futaba 3PM-X coming tomorrow!

    Woohoo! My new Futaba 3PM-X should arrive tomorrow afternoon. I'm going to be replacing the two Traxxas TQs I have for my E-Maxx, the original TQ and a TQ3 I purchased for the 2-speed kit. Both of...
  5. Thread: 2 speed

    by Adam2104
    Replies
    5
    Views
    914

    I run the two speed kit in my 3905 with two...

    I run the two speed kit in my 3905 with two 7-cell packs, it works fine. I spent most time in 1st gear, which is slower, which helps me keep the motor temps in check.

    I wish I could put both the...
  6. Replies
    560
    Views
    162,887

    Is there any place that sells these bodies...

    Is there any place that sells these bodies already painted / cut? I've got negative skills in both areas, though I think the body looks awesome, there's no chance of me being able to make it look...
  7. Thread: battery wrap

    by Adam2104
    Replies
    20
    Views
    580

    That will ruin NiMH batteries. You should stop as...

    That will ruin NiMH batteries. You should stop as soon as the truck starts driving slower. Running them until the truck doesn't move is NOT good for the batteries.
  8. Replies
    24
    Views
    1,557

    I have the same sets of batteries. ProMatch 4600s...

    I have the same sets of batteries. ProMatch 4600s and some Venom 5000s. To me, the performance is the same with either set. I run them both, whatever I feel like at the moment, and never noticed much...
  9. Replies
    7
    Views
    1,102

    Does the R603FF fit inside the stock rx box?

    Does the R603FF fit inside the stock rx box?
  10. Replies
    8
    Views
    907

    So now I'm in a bit of a tricky situation. With...

    So now I'm in a bit of a tricky situation. With two broken TQ transmitters, that's going to be around $50 w/ shipping to get them replaced via Traxxas. I'm not sure its worth it. With Tower's coupons...
  11. Replies
    8
    Views
    907

    I did some more troubleshooting last night. It...

    I did some more troubleshooting last night. It looks like I have not one bad TQ transmitter, but two bad ones.

    I have four TQs today, one for the Slash, one for the E-Revo VXL, and two for the...
  12. Replies
    4
    Views
    894

    Waterproof aftermarket servos?

    I dig that the stock servos are waterproof. I like running in the water and not having the worry about it. That being said, the stock servos on the 3905 are pretty weak so I'm considering getting a...
  13. You shouldn't have to program is to begin with,...

    You shouldn't have to program is to begin with, as per the manual:
  14. Replies
    8
    Views
    907

    Thanks for the suggestions, however, I've already...

    Thanks for the suggestions, however, I've already tried three different TQ transmitters. A TQ3 and two TQ2s (the original that came with my E-Maxx AND the one from my Slash). The problem exists with...
  15. Replies
    8
    Views
    907

    Batteries causing interference?

    I've been having some trouble recently with my E-Maxx. At random times, the slightest bump of the throttle will cause the truck to creep forward until I hit the brakes or put it in reverse. Other...
  16. Replies
    13
    Views
    730

    Hm, this is the second post I've read that says...

    Hm, this is the second post I've read that says charge them at a low charge rate, under 1amp. When you say longer life battery, do you mean longer run times, or longer, over all, for the life of the...
  17. Replies
    13
    Views
    730

    Charging these little batteries?

    I've got my new mini E-revo on order from Tower Hobbies. It should be here sometime this week (along with some parts to fix my 1/10 Slash). In any case, I understand this little guy uses some smaller...
  18. Replies
    12
    Views
    892

    Pictures please? I have my mini E-Revo on its way...

    Pictures please? I have my mini E-Revo on its way from Tower. It should be here sometime this week. I'd like to get off to a good start and seal this up from the get-go.

    Thanks!
  19. Replies
    11
    Views
    850

    Its stripped, so some of the teeth are missing. I...

    Its stripped, so some of the teeth are missing. I believe I caused the problem by adjusting the gear mesh too loose.
  20. Replies
    11
    Views
    850

    How long does the diff last? The reason I wanted...

    How long does the diff last? The reason I wanted to pull it apart was because I thought the tranny / diff was making a grinding noise. It suppose its possible that was coming from the spur gear...
  21. Replies
    11
    Views
    850

    Open up transmission case?

    Am I correct when I think it takes practically disassembling the entire back end to open the transmission on the Slash?

    I did some hard running this weekend, lots of jumps, loose sand, and I ended...
  22. Replies
    203
    Views
    11,029

    What pinion can you use with the stock 68t spur...

    What pinion can you use with the stock 68t spur gear?
  23. Replies
    9
    Views
    2,726

    Sorry, I didn't find a solution to this. The...

    Sorry, I didn't find a solution to this. The servo saver Traxxas sent didn't make any difference. I'm just going to roll with it like this for now, it isn't causing my any trouble as I don't spend my...
  24. Replies
    203
    Views
    11,029

    Do, if one was to buy a Titan 775, I assume a new...

    Do, if one was to buy a Titan 775, I assume a new motor mount would be necessary unless I want to break out a Dremel. Is the KD motor mount the best option going? If so, what do you use to cover the...
  25. Replies
    203
    Views
    11,029

    Ah, that would make more sense. I thought I was...

    Ah, that would make more sense. I thought I was missing something...
Results 1 to 25 of 140
Page 1 of 6 1 2 3 4