Search:

Type: Posts; User: Hughesne

Page 1 of 5 1 2 3 4

Search: Search took 0.05 seconds.

  1. Replies
    9
    Views
    1,881

    It wasn't a Tekin specific question, it was a...

    It wasn't a Tekin specific question, it was a mechanical question, as the ESC/Motor setup is pretty standard no matter what the brand. Wasn't breaking any forum rules.

    To answer the question, I...
  2. Replies
    9
    Views
    1,881

    Is it even a valid assertion that running 6s on...

    Is it even a valid assertion that running 6s on an esc that supports 6s has fried because the motor doesn't support 6s? I would understand the motor blowing if the motor rpms were going over 60k,...
  3. Replies
    9
    Views
    1,881

    I had it at 4S and wanted more. How do you have...

    I had it at 4S and wanted more. How do you have it geared?
  4. Replies
    9
    Views
    1,881

    Tekin Rx8 with 2250kv T8 motor on 6S

    As seen in another thread, i recently fried this ESC. After talking with support, i guess I never realized that the 2250 T8 motor is only rated for 4S. I could have swore that others are running a...
  5. Replies
    12
    Views
    856

    I'll buy a 20 tooth and try it out. If Tekin...

    I'll buy a 20 tooth and try it out. If Tekin wont give me some sort of trade on a RX8 gen2, i may switch to MM2, never used a castle, seem to be more basher proof and Tekin is more race proven, my...
  6. Replies
    12
    Views
    856

    1 tooth can't be the difference between fried and...

    1 tooth can't be the difference between fried and perfect.
  7. Replies
    12
    Views
    856

    I didn't notice before, but the bottom of the esc...

    I didn't notice before, but the bottom of the esc is melted. Not happy right now, 2nd melted esc in a year. I run 6s 21/54 all the time without issue, why this time? Nd 2 failure in a year is a lot...
  8. Replies
    12
    Views
    856

    Nothing powers on at all. To bypass the switch...

    Nothing powers on at all. To bypass the switch should I just clip the 2 wires and splice them?
  9. Replies
    12
    Views
    856

    Yes, 2-3s lipos. I tried some other lipos and...

    Yes, 2-3s lipos. I tried some other lipos and nothing worked. So I eliminated a battery issue.
  10. Replies
    12
    Views
    856

    Diagnose electrical issue

    Was running up and down the street and notice a small spark from behind, then I lost all power. I see no melted wires, or esc, motor, nothing. Batteries are fully charged, all connections are still...
  11. Replies
    21
    Views
    1,317

    I got my CVDs today, was just installing them....

    I got my CVDs today, was just installing them. Does everyone put the boot nearest the diff?

    Also, I have a Tekin RX8 esc, and the throttle set as linear. Maybe I'll back it off to setting 2.
  12. Replies
    21
    Views
    1,317

    Any problems with running the Summit CVD with the...

    Any problems with running the Summit CVD with the RPM TruTrack arms?
  13. Replies
    2
    Views
    141

    Except there is only 1 set on ebay right now, and...

    Except there is only 1 set on ebay right now, and looks fairly used.
  14. Replies
    2
    Views
    141

    WTB-summit driveshaft long

    I would prefer new, but would look at used. I would take 2 or 4. Email nickehughes@gmail.com. Thanks.
  15. Replies
    21
    Views
    1,317

    The CVDs are steel, so what are you saying?

    The CVDs are steel, so what are you saying?
  16. Replies
    21
    Views
    1,317

    I would use them, but I can't see a thin piece of...

    I would use them, but I can't see a thin piece of rubber helping structurally. More to keep dirt out.
  17. Replies
    21
    Views
    1,317

    Twisted stock driveshafts

    5 mins into my new/first 6s batts and HR double slipper both rears literally twisted like a soda straw. I knew running 6s would break more, just didn't expect it so fast. So the question is what do...
  18. Replies
    6
    Views
    810

    I did not buy HR pads, 4 sets of Traxxas AL kits...

    I did not buy HR pads, 4 sets of Traxxas AL kits - 5352r, and also some tmaxx brake pads (4964) as a quadruple backup system when anything goes wrong. I think that makes about a hundo spent so far...
  19. Replies
    6
    Views
    810

    FYI, I found a new 1 on ebay today for $20...

    FYI, I found a new 1 on ebay today for $20 shipped. Bought 4 aluminum rebuild kits and 2 tmaxx brake pads as back ups. Sick of #slipperfail
  20. Replies
    6
    Views
    810

    How i read the slipper break in is to baby it for...

    How i read the slipper break in is to baby it for the first set of packs. Adjusting as needed to slip for 1 second. Ive done that. This last slipper lasted for a few dozen runs before getting too...
  21. Replies
    6
    Views
    810

    HR Double Slipper Avaibility

    After my 2nd aluminum slipper glazed up and warped my spur im switching to something more durable. The HR double is currently out of stock, is this one of those items that is always out of stock or...
  22. Replies
    2
    Views
    718

    Off-center spur gear

    I keep ruining spur gears which still work for a few runs, but are just loud. I have found that the problem is the pinion and spur lineup, but there is play in the input shaft to the transmission,...
  23. Replies
    15
    Views
    1,359

    The problem is that this model (and many others)...

    The problem is that this model (and many others) is called "RTR", which it technically is ready to race. But even out of the box, you need to check the slipper and mesh, that is not clear in the...
  24. Replies
    12
    Views
    901

    So I took some body washers and trimmed them so...

    So I took some body washers and trimmed them so they would only touch the inside ring of the outside bearing. Took some time to get the grub screws back in because it is tight. Too late to take it...
  25. Replies
    12
    Views
    901

    Hate to beat a dead horse, but...

    Im not liking any of the options that ive come across to fix the 17mm traxxas hex wheel slop. The HPI Flux hexes look really generic, I like the blue AL hex hub. The HPP look good, but are...
Results 1 to 25 of 102
Page 1 of 5 1 2 3 4