Search:

Type: Posts; User: MitchD

Page 1 of 14 1 2 3 4

Search: Search took 0.18 seconds.

  1. Thread: Lipo's :D

    by MitchD
    Replies
    17
    Views
    680

    Why not block Associated/Reedy ? They sell...

    Why not block Associated/Reedy ? They sell products with "traxxas compatable battery connections"
  2. Replies
    20
    Views
    565

    I keep pretty good records on my batteries and I...

    I keep pretty good records on my batteries and I had a HK battery fail on me.I have only had it for 13 months and 219 charge/discharge cycles. I have 23 HK batteries in different sizes/capacities so...
  3. Replies
    6
    Views
    430

    Same problem I had. Too much locktite

    Same problem I had. Too much locktite
  4. Replies
    7
    Views
    360

    I use the STRC pins because I was bending...

    I use the STRC pins because I was bending stockers also.I am running the wide mod and I ordered two sets of rear inner and outer pins from Impactrc for around the same price as a regular set.I have...
  5. Replies
    13
    Views
    913

    If you cant find one local I live in Escondido...

    If you cant find one local I live in Escondido and I have a spare you can have
  6. Replies
    9
    Views
    514

    I used a 5X10 bearing with a couple washers.The...

    I used a 5X10 bearing with a couple washers.The 5X10 bearing goes inside the 10X15 bearing so you have two bearings on one shaft
  7. Replies
    0
    Views
    386

    Another solution to axle problems?

    I have a PE with pede tires.I bent axles with stock tires easily.I switched the plastic hexs out for aluminum when I went to pede tires and I did not bend axles quite so easily.When I bent the last...
  8. Replies
    66
    Views
    2,219

    I think Dad summed it up very well.I started out...

    I think Dad summed it up very well.I started out yeears ago with Ni Cads and I saw blowups with them.I have seen blowups with NiMH batteries.I have not seen,I have heard 2nd or 3rd hand about LiPos...
  9. Replies
    2
    Views
    166

    the little pulley thing is a spacer when using...

    the little pulley thing is a spacer when using the wheelie bar.You use the long bolt with a nut and the spacer in between
  10. I finally bent a rear using pede tires.I am also...

    I finally bent a rear using pede tires.I am also using aluminum hexs and Losi springs.When I bent this one it bent at the outer end ,not at the pin hole like when I was running all stock.Also it was...
  11. Maybe you could find BF Goodrich instead?...

    Maybe you could find BF Goodrich instead? Goodwrench is the GM slogan
  12. Replies
    7
    Views
    392

    I am not using the washers.Mine had a bind when I...

    I am not using the washers.Mine had a bind when I put one washer in
  13. Thread: wheelie bar :-)

    by MitchD
    Replies
    13
    Views
    989

    I have that one in black.The only negative is a...

    I have that one in black.The only negative is a lack of adjustability.Two positions ,low and lower
  14. Replies
    10
    Views
    289

    I had this same conversation a year ago including...

    I had this same conversation a year ago including emailing STRC and getting the same answer.Like you I am running TRaxxas aluminum with no very little slop now.i bent the STRC rear tower almost...
  15. Replies
    21
    Views
    697

    10 I think

    10 I think
  16. Thread: REd Arms

    by MitchD
    Replies
    12
    Views
    525

    REd Arms

    RPM now has red a arms.Will be available 3/29
  17. Replies
    14
    Views
    601

    All the soft case batteries from HobbyCity...

    All the soft case batteries from ********* require at least dremeling a slot for the wires
  18. Traxxas 4945,The only thing you will use is the...

    Traxxas 4945,The only thing you will use is the black spring which is stiffer than the silver spring
  19. Replies
    17
    Views
    1,609

    I dont like them.You have to use RPM's hex...

    I dont like them.You have to use RPM's hex adapter.This is the only RPM product I did not like
  20. Replies
    14
    Views
    610

    I have bent axles when stock on the Rusty but...

    I have bent axles when stock on the Rusty but then I switched to Pede tires and I put on aluminum hexs.I have not bent an axle since then. Is it the aluminum hexs providing more support?Same...
  21. Replies
    87
    Views
    10,931

    I was refering to the whole assembly shifting...

    I was refering to the whole assembly shifting front to back because the center drive shaft will allow movement.The original plastic bushing has a flange to keep the shaft from moving back and forth
  22. Replies
    18
    Views
    679

    I cannot run the shock mounts with the GPM...

    I cannot run the shock mounts with the GPM shocks.The shock body binds against the chassis.I have the same problem with the Driven Products chassis brace,the shocks rub against thr brace.
  23. Replies
    87
    Views
    10,931

    I used a flanged bearing because I was worried...

    I used a flanged bearing because I was worried about it moving.
  24. Why not use a 5X10 flanged bearing to replace the...

    Why not use a 5X10 flanged bearing to replace the plastic bushing with a small spacer between the two bearings?I dug one out of my spares box and it looks great.Also if the 10X15 bearing goes out you...
  25. Replies
    4
    Views
    205

    You used the wrong one.You are trying to use the...

    You used the wrong one.You are trying to use the one for the Bandit
Results 1 to 25 of 335
Page 1 of 14 1 2 3 4