Search:

Type: Posts; User: airmaxx23

Page 1 of 20 1 2 3 4

Search: Search took 0.22 seconds.

  1. Replies
    13
    Views
    1,516

    I've been flying my QR-1 a lot this year and...

    I've been flying my QR-1 a lot this year and really like it. I have a total of 16 batteries
  2. Replies
    8
    Views
    789

    Your problem with it not returning to center may...

    Your problem with it not returning to center may be a servo saver problem or a bad servo. I've been using 2 of these for about 8 months and have not had any glitching or centering problems at all.
  3. Replies
    7
    Views
    692

    The spring from the metal saver is quite a bit...

    The spring from the metal saver is quite a bit stiffer and works great with the stock plastic servo saver.
  4. Replies
    17
    Views
    507

    The stock horn works with the Corona servo but...

    The stock horn works with the Corona servo but you need to use the screw that came with the servo or something equivalent. On a side note my Corona servo is still holding up just fine after a lot of...
  5. Replies
    12
    Views
    678

    The Corona 238 is a great servo, I've been...

    The Corona 238 is a great servo, I've been pounding on one for about 7 months now and it's holding up just fine. All of the gears are all metal, the Hitec 5085 still has one plastic gear.
  6. Replies
    14
    Views
    1,102

    I've had 2 of these for a few months now and they...

    I've had 2 of these for a few months now and they are still working great and I abuse them constantly. I waterproofed one that I'm using in my winter rat MERV and it has not gotten sloppy at all as...
  7. Replies
    236
    Views
    11,253

    Awesome work, and they said you couldn't do it...

    Awesome work, and they said you couldn't do it which probably motivated you even more.
  8. Replies
    4
    Views
    288

    Take a small folded piece of paper (very small)...

    Take a small folded piece of paper (very small) and put it in the hole in the bulkhead leaving a little sticking out, it will give the screw something to bite into and should last until your new one...
  9. Replies
    4
    Views
    203

    The stock servo will sometimes fail rather...

    The stock servo will sometimes fail rather quickly and you can get a metal gear, ball bearing high torque servo (Corona DS238MG) for 1/5 of the price you'd pay for something comparable to it.
  10. Replies
    4
    Views
    203

    Edit your thread, you can't say the name of the...

    Edit your thread, you can't say the name of the company that you listed. I wonder why the filter didn't kick in though.
  11. Replies
    18
    Views
    820

    That's too funny, I just bought a new tackle box...

    That's too funny, I just bought a new tackle box to replace one of these that I've had for a few years. I know what I'm going to with now, thanks.
  12. Replies
    7
    Views
    157

    You can take the case apart and fill it with...

    You can take the case apart and fill it with dielectric grease, once it's back together put a nice blob of it where the servos plug in then plug them in accordingly. I used to do this all the time...
  13. Replies
    33
    Views
    2,157

    I only use Deans connectors, they are very easy...

    I only use Deans connectors, they are very easy to unsolder when needed and are a lot less bulk than the Traxxas connectors. I've never had an issue getting the apart but I do hold onto a little of...
  14. Replies
    26
    Views
    502

    The stock 1/16 summit axles look just like the...

    The stock 1/16 summit axles look just like the bigger ones but without the boots, the plastic is more brittle on the 1/16 summit axles when compared to the 1/16 MERV axles. I had traxxas CVDs for a...
  15. Replies
    16
    Views
    895

    I've done it across a 70-80 foot pool of water...

    I've done it across a 70-80 foot pool of water that was only about 14" deep using Summit tires.
  16. Going lower on the spur and/or higher on the...

    Going lower on the spur and/or higher on the pinion. Just be sure to watch your temperatures.
  17. Replies
    1
    Views
    134

    Yes you can, the 1/16 Summit rocker are LT. It...

    Yes you can, the 1/16 Summit rocker are LT. It does make the truck hard to handle at speeds though.
  18. I got a warning for quoting your edited language....

    I got a warning for quoting your edited language. Something like that should be in the rules, which it isn't, so others are aware of it.
  19. Replies
    1
    Views
    120

    Here ya go... ...

    Here ya go...

    http://traxxas.com/forums/showthread.php?8969232-Crazy-twin-motor-MERV-project...-any-ideas&highlight=twin+motor
  20. Sorry for the double post, not sure how that...

    Sorry for the double post, not sure how that happened.
  21. Why did I receive warning for language when it...

    Why did I receive warning for language when it wasn't me who posted it? The language was filtered in the post I replied to not my response.
  22. Replies
    10
    Views
    491

    Thanks, that's what I thought.

    Thanks, that's what I thought.
  23. Replies
    10
    Views
    491

    Where are you using the Shoo Goo on the...

    Where are you using the Shoo Goo on the bulkheads? An air compressor works great for getting the excess WD-40 off of the truck when you're done.
  24. 1/8 scale has bigger bearings and gears but also...

    1/8 scale has bigger bearings and gears but also a lot more power, like you said, the only why to find out is to try them. Hopefully they work out.
  25. I've had the spiral bevel gears in a few...

    I've had the spiral bevel gears in a few different 1/8 buggies and never had issues with the pinion bearings.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4