Search:

Type: Posts; User: larsen8

Page 1 of 20 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    64
    Views
    4,584

    This is an incredibly late reply and you have...

    This is an incredibly late reply and you have likely already found the answer to your questions. But, here goes:
    I was running the double orange springs and 70wt oil all the way around at the time...
  2. Replies
    64
    Views
    4,584

    They are indeed bead locks. Axial Rocksters with...

    They are indeed bead locks. Axial Rocksters with Proline Moab XL's. Still running these tires two years later.....
  3. Replies
    57
    Views
    3,848

    Apparently the rules have not changed.

    Apparently the rules have not changed.
  4. Replies
    57
    Views
    3,848

    I take that back. My BEC can handle up to 12s...

    I take that back. My BEC can handle up to 12s lipo input. I don't know if forum rules have changed regarding posting other name brands, but I am using a ********* YEP 20A HV SBEC.
  5. Replies
    57
    Views
    3,848

    Yes, there is 4s input on the BEC. My BEC can...

    Yes, there is 4s input on the BEC. My BEC can handle up to 6s I believe.
  6. Replies
    57
    Views
    3,848

    Yes, that is absolutely right. However, I don't...

    Yes, that is absolutely right. However, I don't think having that extra negative wire there would do any damage. But I'm not sure on that so don't quote me.

    Also, I recently wired up my Summit...
  7. Thread: Dewalt rust

    by larsen8
    Replies
    20
    Views
    737

    You could always try spreading a very light...

    You could always try spreading a very light coating of gun oil on the can of the motor after you clean it. It's meant to protect guns from rust and corrosion, so I imagine it will do the same for...
  8. Replies
    3
    Views
    237

    If you disconnect the servo arms, take off the...

    If you disconnect the servo arms, take off the whole front skid plate set (three separate pieces), and then disconnect both steering tie rods, you will find that the entire servo saver assembly will...
  9. Replies
    57
    Views
    3,848

    Good info. Thanks. However, I was not wondering...

    Good info. Thanks. However, I was not wondering about whether the BEC could handle the current, but rather if the servo wires and connectors could.



    THANK YOU. That has been one of my...
  10. Replies
    57
    Views
    3,848

    Close. You will want to remove the red...

    Close. You will want to remove the red (positive) wire from the ESC-to-RX lead. The signal wire needs to be there for the RX to communicate with the ESC. Removing the red wire disables the ESC's...
  11. Replies
    57
    Views
    3,848

    I'm really just going on theory here. At this...

    I'm really just going on theory here. At this point I'm no longer concerned about specifics like ESC wiring, voltage, etc. I'm trying to figure out what works and what doesn't. I already know how...
  12. Replies
    57
    Views
    3,848

    So how exactly is #1 powering only the servo and...

    So how exactly is #1 powering only the servo and #2 is powering both? Not being rude, just don't know. I know very little about electronics but this baffles me. In both pictures there are power...
  13. Replies
    57
    Views
    3,848

    Can someone please explain to me the difference,...

    Can someone please explain to me the difference, if any, between 1 and 2? As I understand it, both could be used to power both the RX and the servo.
    ...
  14. Replies
    57
    Views
    3,848

    To whom it may concern: I just wired a BEC into...

    To whom it may concern:
    I just wired a BEC into an Axial Wraith via this setup. The servo is running on 7.4v and all seems to be working well....
  15. Replies
    9
    Views
    450

    ^+1 A properly adjusted servo should last a while

    ^+1 A properly adjusted servo should last a while
  16. Replies
    57
    Views
    3,848

    Exactly. The other battery need not be...

    Exactly. The other battery need not be soldered/touched/looked at/thought about. You're only going to wire the BEC into one battery. Make sure to wire it into the BEC side of the ESC though.
    ...
  17. Replies
    57
    Views
    3,848

    Jamann did something like this I believe....

    Jamann did something like this I believe.
    http://i1205.photobucket.com/albums/bb433/larsen8or117/BEChookup_zps293243a6.jpg

    I'm going to wire my BEC to both packs simply for the purpose of...
  18. Replies
    57
    Views
    3,848

    Good info. Thanks a bunch. But let me rephrase...

    Good info. Thanks a bunch. But let me rephrase my original question:
    How many amps do you think a high torque servo (6v or 7.4v, around 350oz/in torque) would be pulling on average?
  19. Replies
    57
    Views
    3,848

    I know that some people use the stock connectors...

    I know that some people use the stock connectors and/or power the rx directly with the BEC while using higher power servos. I'm confident that in most any racing or bashing setup that would work,...
  20. Replies
    57
    Views
    3,848

    With this servo being used in the Summit for...

    With this servo being used in the Summit for crawling applications, is it possible that the servo is going to overdraw amps? Do you think with these higher power servos, the servo connectors/RX can...
  21. Replies
    9
    Views
    450

    I went through three tranny shift servos in a few...

    I went through three tranny shift servos in a few weeks when my Summit was new. Then I took a few minutes and manually adjusted the servo so that it was never pushing farther than it was able to...
  22. Replies
    57
    Views
    3,848

    And I will be happy to give anyone a tutorial on...

    And I will be happy to give anyone a tutorial on how to use Paint. :P
  23. Replies
    57
    Views
    3,848

    External BEC to Servo Amp Draw

    Ok. Before you all start telling me to use the search feature, I have been reading threads from many different forums for a while now and can't find a clear answer.
    With a single high torque servo...
  24. Replies
    16
    Views
    490

    Servos are all adjusted and quiet. No, I have...

    Servos are all adjusted and quiet. No, I have not installed a glitch buster. I'm running a JR ultra high torque servo for the steering. It's not a high voltage servo. What's confusing me is that...
  25. Replies
    16
    Views
    490

    I'll try that. But another thing is that...

    I'll try that. But another thing is that supposedly with a 2.4 GHz. radio you shouldn't even need caps on the motor. I tried pulling all of them off temporarily, and the truck behaved exactly the...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4