Search:

Hey. Been out of the scene for close to a year due to no time to drive and battery issues. Changed to a move survivalist scene but want to get back into the rc scene. I have an emaxx with a dewalt...

What nimh's are those?

The cost is is the only problem and that's why I've been on hold with my maxx for 3months...I'm only 15 and I have to get my dad to order everything I need off the internet if the lhs doesn't have it...

Is there any benefit to these cvd style driveshafts I've been seeing, and can I use cvd's for the a-arm driveshafts and the regular ones for the center shafts? Those are still tight and don't have...

I'm still using my original 3905 E-maxx drive shafts that it came with. I have a few questions about when to replace or upgrade from wear. They have some slack to them when I roll it forward. About...

I think my Promatch's are done:mellow: I cycled them four times each discharge was at 2amps and charge rates were .8, 1.5, 3.0, and the usual 5.0 I use normally. They still haven't regained their...

I may wanna go LiPo soon with my Dewalt setup. Possibly around the end of this year cause Ima save up during the summer and my bday is 4 days before christmas so I have plenty of time. What are some...

Ok...I have a pair of promatch 7cell 5000mah batteries and I think I've killed another cell once again. I don't know how but the same cell as last time that I killed somehow (I don't know about that...

The small wires handled the load just fine. The motor ran well regardless of how hot it got. It didn't have an "all the time temp" because some days the ambient temp would cool it down or heat it up.

Wait!!! I used the same motor as well in my first dewalt project and got capacitors on it. You have to take some insulation off the wire (small area where you solder), and solder to your motor can....

I have 2 different kinds of capacitors. There both ceramic disk style. One is has the #104 on it and the other two have #345. Is it possible to use these two kinds together because I need to wire up...

Ive noticed that as well but, I now thats not the problem always because even when I'm on a high traction surface in my neighborhood. The front end won't even pick up off the ground at all. Not even...

I do have that discharger. I discharged them last with that about 2 weeks ago. Il try them straight off the charger this friday.

I usually charge them as I'm doing something else like tweaking the truck or some other time consuming task. Aren't you supposed to let them cool before use?

Well...I usually go out about 30mins to an hour after their done charging so they have cooled off when I decide to go out with them. Next time I go out il try them straight off the charger. I use a...

Hey. If I decided to solder my motor directly to the esc's wire leads would I still need capacitors? I need to replace the motors brushes and thats gonna be a hasle and I'm not sure how to get the...

I will check my brushes then...now I gotta undo my capacitors lol. How short or long should the brushes be then? Im using traxxas connectors. my gearing is quite low I think compared to other people...

None of the cells are bad-they are all around the same voltage wit heach other in both packs. All the cells are even with temp after I run them. I dont know if there too hot or not because I dont...

I run promatch racing 7cell 5000mah batts. Iv'e noticed that I now have to run mty truck for a few minutes to get my truck to wheelie...Like the batts aren't powerful enougfh at the start of a run...

Support our troops and all they do...SEMPER FI.

Are those composite ones still strong enough?

I want to get some new rims for my big joe's I also dont wanna spend too much money either. I like the proline tech 5 wheels but I dont have 17mm hex yet but I also like dish wheel style but I'm not...

I do have to squeeze the batts through to get them in lol. But they get in. I had to grind my tranny case a little for the original 12v to fit...and a little more for the 14.4v i have now. I run...

Ive done the mod as well with a 12v and a 14.4v...Had the 12v first then switched it over to a 14.4v. I run 86 spur with a 18t pinion and the motor now just touches it perfectly. I put 4 spacers on...

Yes the helmet was necessary lol. I didn't buy it to not use it. I live in a private community and I always see where the security is no ones gonna see me. I'm still going out today even though its...