Search:

Type: Posts; User: 79Broncojoe

Page 1 of 3 1 2 3

Search: Search took 0.00 seconds.

  1. Hope this works ...

    Hope this works

    http://i1285.photobucket.com/albums/a588/summitsinvictoria/MotorConnection_zps6b6b4e8c.jpg
  2. Is my motor done when the terminal breaks?

    So I have steering but no throttle. Didn't take long to see the motor electrical Red Wire connection that comes out of the end bell has a 90" degree bend up where the wires are attached broke clean. ...
  3. This is what I use!...

    This is what I use!
    http://i1285.photobucket.com/albums/a588/summitsinvictoria/SummitStand_zpsc3f9effc.jpg
    http://i1285.photobucket.com/albums/a588/summitsinvictoria/Summitonstand_zps49a031b9.jpg
  4. "I made a Canadian version" should work in every...

    "I made a Canadian version" should work in every other Country but Germany, Sorry!
    I need to find an easier way to find artist that aren't so picky, lol

    Enjoy!...
  5. Thanks for the feedback, I spent a fair amount...

    Thanks for the feedback,
    I spent a fair amount of time building this video and was just as excited with the choice of music. Little did I know, NICKELBACK a Canadian Artist blocks his music in...
  6. Oh, I see what you are talking about, I will...

    Oh, I see what you are talking about, I will change the music and repost it.
    I just found out this does not play in Canada or Germany, errr
  7. Not sure what your talking about, it was your...

    Not sure what your talking about, it was your choice! lol
  8. Eh Cool Summit Video (summitsin victoria)

    Check it out! This is my son and I crusin not far from home, place called Mill Hill.
    I have never placed a video here before so hopefully its ok.

    summitsin victoria
    http://youtu.be/8gpD4m9nB3Q...
  9. Replies
    13
    Views
    687

    Update on The bec; I have ran the summit on a...

    Update on The bec;
    I have ran the summit on a gnarly Billy goat trail, very cool. I find swinging those oem tires back and forth actually helps getting over difficult obstacles in which the OEM...
  10. Replies
    4
    Views
    260

    Good question as I am also waiting on my local...

    Good question as I am also waiting on my local supplier to stock the 2065. I have read a post that you could use a 2080 servo, little bigger, little stronger with a little bit of mod to be done....
  11. I replaced the small ring side output shaft last...

    I replaced the small ring side output shaft last night, I have shims but the diff has low miles on it, no side play soo no shims were used! However by adding shims, I did find on occasions it...
  12. Good job and perfect timing!, I also have...

    Good job and perfect timing!, I also have temp\voltage sensor to install,

    summitsin victoria
  13. I would agree with you but in my case he got a...

    I would agree with you but in my case he got a stick stuck in his rear wheel, and probably being 8 years old thought he could ride it out, lol...not!
    The crappy thing about it is, I have to fix it...
  14. Replies
    13
    Views
    687

    Seems the noise is from the servo aligning...

    Seems the noise is from the servo aligning itself, but having the summit upside down, at times was still making that noise.
    I am going to install a BEC, this will give me more torque from the 7950....
  15. I incorporated on the right side of the...

    I incorporated on the right side of the workbench, pockets for the hand radios. This will keep them safe and I always no where they are. My air compressor and strip bar are installed and now...
  16. Replies
    13
    Views
    687

    I just installed a Hitec 7950; I had to turn down...

    I just installed a Hitec 7950; I had to turn down the music as I thought the ballast in the fluorescent light was humming. It was my Hitec, head lights seem to flash when turning which can be a sign...
  17. As I look at these pic's, it seems we all started...

    As I look at these pic's, it seems we all started with smaller versions of RC's, great pic's much appreciated!

    My next plan is building compartments on the side of my workbench for safe storage of...
  18. Got it. thanks for the tip! This picture was...

    Got it. thanks for the tip! This picture was suppose to be 1st following the above,
    http://i1285.photobucket.com/albums/a588/summitsinvictoria/OriginalRCBench_zpsa2cfbe81.jpg
  19. http://i1285.photobucket.com/albums/a588/summitsin...

    http://i1285.photobucket.com/albums/a588/summitsinvictoria/01-WorkBench03-30-13_zpsa26769a4-1_zpsf91dd5f4.jpg
  20. Could someone please tell me how to post a...

    Could someone please tell me how to post a complete picture, I added a url above, just gave me above address.
    EDtoys above is what I want to do! tried copy, paste no luck
  21. Great Pic’s, I don’t have a separate room for my...

    Great Pic’s, I don’t have a separate room for my RC, My farther built this work bench around 14 years ago, most of which has been in storage until recently when buddy bought a summit, and I had the...
  22. OK, you got my attention on the Ultrasonic...

    OK, you got my attention on the Ultrasonic cleaner, interesting but pricey
    I am not sure what I would use the dremel tool for, care to eleaborate?
  23. Looking for Ideas, Pic's of your Summit Workshop,

    I am looking at turning my summit work table into a totally Cool Summit Mechanics Bay
    Features will be

    - 110 strip bar
    - Adjustable directional light
    - Soldering station
    - Shelving for...
  24. Replies
    20
    Views
    781

    Instead of buying a spool, could you not glue...

    Instead of buying a spool, could you not glue (epoxy) the locker hub into the carrier?
  25. Replies
    1
    Views
    258

    Question about RE RE 2065 for 2080

    I have only seen 1 posting in regards to replacing the 2065 transmission servo for the 2080 and I am looking at getting more feedback on this topic.

    My supplier may not have the 2065 servo this...
Results 1 to 25 of 55
Page 1 of 3 1 2 3