Search:

Type: Posts; User: 1badrz28

Page 1 of 4 1 2 3 4

Search: Search took 0.24 seconds.

  1. Replies
    20
    Views
    388

    The HR was way too stiff as a saver. I added the...

    The HR was way too stiff as a saver. I added the bell crank arm from the factory steering. The plastic on metal is smoother that the aluminum on aluminum.

    After the fact, it was waste of money.
  2. Replies
    42
    Views
    761

    I bought the Venom Medion charger, I am very...

    I bought the Venom Medion charger, I am very happy with the unit. The reason i went with them is because I use all Venom batteries. Their warranty was no hassle whe nI had a battery go down. Only...
  3. Replies
    16
    Views
    426

    Sidewinder was the best urgrade I ever did to the...

    Sidewinder was the best urgrade I ever did to the MERV.
  4. Replies
    12
    Views
    306

    Easier to clearance it now , than have debris in...

    Easier to clearance it now , than have debris in there that you need to clean out later.
  5. Replies
    10
    Views
    334

    I'm two chassis in, two front bulkeads, shocks,...

    I'm two chassis in, two front bulkeads, shocks, from speed runs. replaced the ESC with an SV2, Traxxas axle... only original part is the can now, Stock pieces were too cheap to not replace after afew...
  6. Replies
    10
    Views
    276

    I heat mine just until it starts to slightly...

    I heat mine just until it starts to slightly bubble, keep it in the heat for about an hour, than let it cool down over night.
  7. Replies
    13
    Views
    302

    GH is a nice mount and seals up real well.

    GH is a nice mount and seals up real well.
  8. Replies
    5
    Views
    163

    Shock oil and spring swaps can change the...

    Shock oil and spring swaps can change the dymanics of how the car enters and leaves a jump. I run the same jump and tuned to that one. If you use a bunch of different jumps than throttle control is...
  9. Replies
    11
    Views
    367

    Just swapped out to the one hole pistons and the...

    Just swapped out to the one hole pistons and the truck sure responds a lot better. I like a soft stable compression and that fit the bill. Sure keeps the truck from bouncing. I also have blue springs...
  10. Replies
    22
    Views
    566

    I have the HR one, and it works well. No...

    I have the HR one, and it works well. No complaints at all.
  11. Replies
    6
    Views
    224

    I was brushless and finally blew out the stock...

    I was brushless and finally blew out the stock esc using 4s.

    Not sure on the motor mount swap.
  12. Same here, Sometimes you get a few teeth that...

    Same here, Sometimes you get a few teeth that are not smooth, like they said,after a few packs it wears in.

    I'll take tight over loose any day.
  13. Replies
    6
    Views
    224

    I just installed a used SV2, plug and play for...

    I just installed a used SV2, plug and play for me.


    Seems to be a lot more braking capability.
  14. The GH motor mount is worth the investment for...

    The GH motor mount is worth the investment for fitment. I have been happy with mine at half the price of the King Headz.

    We are just upgrading for the larger bearing and aluminum in which it has...
  15. Replies
    3
    Views
    194

    I have been 57mph on the Summit tires, they...

    I have been 57mph on the Summit tires, they balloon quite bad. I had to extend my wheelie bar mount to keep the front tires on the ground. They wear really well, but I found it to tip over real easy...
  16. Replies
    13
    Views
    490

    I had the Primal for my first charger. It was a...

    I had the Primal for my first charger. It was a great entry level charger for my son and I's 5 batteries to charge. Not all done at the same time, but we'd go out every few days, One small drop took...
  17. My screws were too long when mounting the 2400...

    My screws were too long when mounting the 2400 motor to the motor plate , so I just shortened the screws.
  18. Replies
    7
    Views
    357

    Than learn to deal with a broken MERV or simply...

    Than learn to deal with a broken MERV or simply run it in training mode until they strip.



    It's a 30 minute job that is not difficult for the average person.
  19. Replies
    18
    Views
    393

    Don't forget to add bearings and take the...

    Don't forget to add bearings and take the bushings out. Easy cheap upgrade.
  20. Replies
    11
    Views
    461

    Corona is nice and strong, direct drop in besides...

    Corona is nice and strong, direct drop in besides a little massaging on the chassis to get it in. I used the factory linkage and horn.
  21. Replies
    24
    Views
    577

    Diff shims, RPM bumpers, wheelie bar, black and...

    Diff shims, RPM bumpers, wheelie bar, black and tan springs or ACE hardware springs if you are jumping alot. Over time you will need axles,steering knuckles, and a new servo.
  22. Thread: New esc

    by 1badrz28
    Replies
    6
    Views
    224

    'I didn't have .080 aluminum around the house so...

    'I didn't have .080 aluminum around the house so I used .079 steel. The steel will be better handling the vibrations and rollovers than the aluminum, especially when you slide in the esc a few times....
  23. Replies
    3
    Views
    201

    I bought the Snap On edition which cam with a...

    I bought the Snap On edition which cam with a lipo... Other than that, no advantage. I tore the body up in a week. As of now, the chassis and bulk heads are the only stock parts it has left. I'd buy...
  24. Replies
    15
    Views
    356

    check the a-arms first. I had the RPM A arms warp...

    check the a-arms first. I had the RPM A arms warp and it made the chassis look twisted. The steel hollow balls and axle carriers really tightened my steering up. There is still about 1/4" total side...
  25. Replies
    84
    Views
    2,260

    Velco is ral easy to do. I opted to put 4 slits...

    Velco is ral easy to do. I opted to put 4 slits in the battery tray and feed the velcro through there. I feel a lot more confident with the velco than the broken battery mounting pins I've been...
Results 1 to 25 of 86
Page 1 of 4 1 2 3 4