Search:

Type: Posts; User: martin_dk

Page 1 of 6 1 2 3 4

Search: Search took 0.43 seconds.

  1. Replies
    6
    Views
    297

    Yeah, you might as well short the powerswitch,...

    Yeah, you might as well short the powerswitch, its going to fail sooner or later - and it sounds like it just did..
  2. Replies
    12
    Views
    681

    So, I finished the conversion. Ended up with a...

    So, I finished the conversion. Ended up with a Savox SV1270TG. I run it at 7V - just to be safe. As chapinb suggested I power the servo directly from the bec and then run the control wire from the rx...
  3. Replies
    24
    Views
    754

    Hmm, doesn't look compatible with tekno sways..

    Hmm, doesn't look compatible with tekno sways..
  4. Replies
    15
    Views
    601

    Regarding diffs I must add that I never had a...

    Regarding diffs I must add that I never had a problem with mine (running 4S) - maybe I'm lucky.. For me the CVD's are a must, I found that the stock shafts are just too weak at the joints. I have...
  5. Replies
    3
    Views
    135

    It can also be a grain stuck in the spur,...

    It can also be a grain stuck in the spur, happened to me more than once..
  6. Replies
    7
    Views
    434

    I read somewhere (just now) that the sidewinder...

    I read somewhere (just now) that the sidewinder 1/8 is rated at 90A compared to the MMM's 120A. So there is a difference, just odd it doesn't say on castle's sidewinder 1/8 page (correct me if I'm...
  7. Replies
    12
    Views
    681

    Yeah, that would just require common ground I...

    Yeah, that would just require common ground I guess.
  8. Replies
    7
    Views
    434

    What's Castle's reasoning behind this new...

    What's Castle's reasoning behind this new sidewinder? I mean its specs are awfully close to the MMM, but its much cheaper.
  9. Replies
    12
    Views
    681

    Thanks for you replies, much appreciated. I think...

    Thanks for you replies, much appreciated. I think I'll go with an external bec then, the reason for me being a bit hesitant on that is that I'm in europe and the castle products are so **** expensive...
  10. Replies
    12
    Views
    681

    Thanks for answering :) I'm considering the...

    Thanks for answering :) I'm considering the SA-1283SG instead, it costs a bit more and is also a bit "weaker" but somewhat faster than the 1230. I'll try w/o a bec at first and see how it goes..
  11. Replies
    12
    Views
    681

    Single servo vs MMM bec voltage

    Hi

    I'm about to take the plunge and convert to single servo and I'm thinking of using the savox 1230tg. The question is; is it really necessary to add an external bec when the mmm delivers 5.5v (I...
  12. Replies
    31
    Views
    1,853

    CVS's: 5451R Ext. cup's: 5153R

    CVS's: 5451R
    Ext. cup's: 5153R
  13. Replies
    31
    Views
    1,853

    I run 4s exclusively and have done so for several...

    I run 4s exclusively and have done so for several years now. In my time I've stripped one diff and that was my fault for having the slipper too tight (happened soon after upgrading to MMM). The only...
  14. Replies
    7
    Views
    311

    The spur was the culprit. I didn't seem that worn...

    The spur was the culprit. I didn't seem that worn to me, I'm used to running the 1:10 revo, so I guess I need to adjust my mind to the smaller scale (including wear-inspection) when working on the...
  15. Replies
    7
    Views
    311

    Ok, thanks, seems like a front diff+bulk...

    Ok, thanks, seems like a front diff+bulk inspection is in order..
  16. Replies
    7
    Views
    311

    Transmission problem

    The kid's vxl started "ticking" when accelerating hard on high traction surfaces = high torque through transmission. So I checked spur - spur like new. Took apart rear diff - no fluid, but gears...
  17. Replies
    6
    Views
    1,662

    http://traxxas.com/forums/showthread.php?461979-pa...

    http://traxxas.com/forums/showthread.php?461979-part-5329
  18. Replies
    4
    Views
    169

    TX reset did the trick :-)

    TX reset did the trick :-)
  19. Replies
    4
    Views
    169

    brand new, cant turn right

    my son just got his brand new revo 1/16, but it wont turn right - only very very little. Left turn is fine. Trim is centered. HELP!
  20. Thread: Disappointed

    by martin_dk
    Replies
    9
    Views
    1,212

    If you don't like/want wheelies then drop in a...

    If you don't like/want wheelies then drop in a center diff..
  21. Replies
    18
    Views
    1,459

    Myself and two buddies of mine run with Futaba...

    Myself and two buddies of mine run with Futaba 3pm 2.4g, we're all very happy with it.
  22. Got mine from modelsport as well, mounted on hpi...

    Got mine from modelsport as well, mounted on hpi warlocks: http://www.modelsport.co.uk/index.php?product_id=24600
    Works like a charm :-)
  23. Replies
    12
    Views
    1,007

    check front+rear diffs

    check front+rear diffs
  24. Thread: Revo Fin Cam

    by martin_dk
    Replies
    12
    Views
    1,438

    "This video contains content from Sony Music...

    "This video contains content from Sony Music Entertainment, who has blocked it in your country on copyright grounds."
    :(
  25. Replies
    16
    Views
    1,411

    Awesome! Fellow dane I presume ;- )

    Awesome! Fellow dane I presume ;- )
Results 1 to 25 of 128
Page 1 of 6 1 2 3 4