Search:

Type: Posts; User: mnewbolds

Page 1 of 12 1 2 3 4

Search: Search took 0.36 seconds.

  1. Replies
    6
    Views
    330

    Also, if you use the stock replacement, you can...

    Also, if you use the stock replacement, you can flip the shoes around and get a better "grab" wont last as long but you can tell the difference.
  2. 2 speed reverse! Sweet!

    2 speed reverse! Sweet!
  3. Replies
    4
    Views
    204

    Had the same issue. Actually, the guy I bought it...

    Had the same issue. Actually, the guy I bought it from had the same issue. He couldn't sort it out. Did what Double G stated and it solved the issue. Also make sure you follow the manual when you set...
  4. Replies
    9
    Views
    706

    +1^… I use this along with 3mm screws, washers,...

    +1^… I use this along with 3mm screws, washers, and nuts to sandwich the rubber and the lexan for a no fail clip retainer. Just poke a small hole in the clip retainer and install it like normal, then...
  5. Replies
    64
    Views
    3,717

    Just swapped out the front bulks. unfortunately...

    Just swapped out the front bulks. unfortunately the rears I bought won't fit.... Not real happy since I bought them as they came into hobby town via ups. Ugh the frustration of pulling all that...
  6. Please explain. I have a 1rst gen that will not...

    Please explain. I have a 1rst gen that will not not run software versions high enough to support the app. 3.1.3 is the highest gen 1 is capable of to my knowledge.
  7. Thread: 3.3 problems

    by mnewbolds
    Replies
    6
    Views
    231

    Remember this though, the factory carb settings...

    Remember this though, the factory carb settings are a starting point to reffer to. Just make sure you are keeping track of where you are on your tune and write it down along with outside temps and...
  8. Thread: 3.3 problems

    by mnewbolds
    Replies
    6
    Views
    231

    New glow plug should help. Sometimes they test...

    New glow plug should help. Sometimes they test well but it might be on its way out and not staying hot enough after the wand is removed.
  9. 2nd gen to 4th gen only as far as I know. I...

    2nd gen to 4th gen only as far as I know. I bought a 1st gen and the software is too old to be compatible with the app. My finances 3rd gen works but good luck, I gotta wait till she isn't looking.
  10. Replies
    9
    Views
    550

    With minimal modification the 775 traxxas motor...

    With minimal modification the 775 traxxas motor will do well in these trucks, as far as I have seen personally. Kershaw designs has some cool stuff but I haven't seen it in person so I can't give...
  11. Replies
    13
    Views
    478

    No, actually I was thinking the spring on the...

    No, actually I was thinking the spring on the stock savers are adjustable but I was mistaken.
  12. Replies
    13
    Views
    478

    Just out of curiosity. You say you keep tearing...

    Just out of curiosity. You say you keep tearing up servos, is your servo saver set too tight? Just a thought.
  13. Replies
    13
    Views
    478

    This is the one I have used. ...

    This is the one I have used.
    ...
  14. Replies
    13
    Views
    478

    I have a hitec waterproof in my crawler but the...

    I have a hitec waterproof in my crawler but the price is slightly higher than the stock servos. In my opinion, the 2075 traxxas servos do a fine job in the emaxx, as long as both are working...
  15. Replies
    64
    Views
    3,717

    Appreciate playing guinea pig for the rest of us....

    Appreciate playing guinea pig for the rest of us. I had I feeling I needed to hold off on these bulks. I planned originally to order 4 sets to do all of my trucks. Man, talk about dodging a bullet....
  16. Replies
    5
    Views
    442

    Did you get the hobbywing? How do you like it?

    Did you get the hobbywing? How do you like it?
  17. Replies
    2
    Views
    257

    They might close this thread but you might have...

    They might close this thread but you might have better luck looking on towerhobbies.com, rcplanet.com or others. Also this would be better suited for the E-maxx brushless forum. Good luck!
  18. Replies
    10
    Views
    349

    In the comments for the video he stated that he...

    In the comments for the video he stated that he used the rev/fwd servo and a cable to lock the front wheels and removed the front shaft. Not sure exactly how but maybe that'll get some creative...
  19. Replies
    5
    Views
    341

    Fyi. Rpm makes white arms... You could dye them...

    Fyi. Rpm makes white arms... You could dye them too.
  20. Replies
    9
    Views
    367

    Just don't do like I did and forget to put the...

    Just don't do like I did and forget to put the second gear in the trans, and then wonder why it won't shift... :lol:
  21. Replies
    18
    Views
    599

    There is another thread on this forum that is...

    There is another thread on this forum that is subject toe/in toe/out. It has a very good explanation of different setups for different traction surfaces.
  22. Replies
    5
    Views
    616

    I like to use losi tire glue. Found at most hobby...

    I like to use losi tire glue. Found at most hobby shops. But I've never had luck re gluing old tires. Try putting the tire in the bead and pulling back slightly. Add small amounts leaving a gap...
  23. Replies
    23
    Views
    634

    Ummm... I can't see 'em. Is it just me?

    Ummm... I can't see 'em. Is it just me?
  24. Replies
    3
    Views
    118

    Yup, 50 wt is a pretty good way to go. 2 or 3...

    Yup, 50 wt is a pretty good way to go. 2 or 3 hole pistons.
  25. Replies
    10
    Views
    208

    I use windex to wet the back of the decal and the...

    I use windex to wet the back of the decal and the surface of the body. Then you can make adjustments when you put it on and use a squeegie or soft card to rub out the bubbles. Works everytime!
Results 1 to 25 of 299
Page 1 of 12 1 2 3 4