Search:

Type: Posts; User: robert f.

Page 1 of 2 1 2

Search: Search took 0.04 seconds.

  1. Thread: Wheelies

    by robert f.
    Replies
    18
    Views
    536

    Hi What size spur gear? What size clutch bell? ...

    Hi What size spur gear? What size clutch bell? Lower size clutch bell numbers and higher spur gear numbers mean more power and less top end. Usually 19 or 20 on clutch bell and 72? on spur gear....
  2. Replies
    28
    Views
    830

    Hi For 3mm inserts for the transmissiion try...

    Hi For 3mm inserts for the transmissiion try tony's screws, much better price!
  3. Thread: Bell clutch

    by robert f.
    Replies
    2
    Views
    134

    Are you connecting the spring ends over the spot...

    Are you connecting the spring ends over the spot where the clutch opens up? Those ends should be connected over a spot where the clutch is not opening.
  4. Replies
    8
    Views
    398

    Maybe a broken clutch spring? Try replacing it. ...

    Maybe a broken clutch spring? Try replacing it. Or maybe your clutch is installed backwards.
  5. Replies
    9
    Views
    547

    Hi I would suggest replacing your chassis braces...

    Hi I would suggest replacing your chassis braces with aluminum ones for a more stable chassis with less flex
  6. Replies
    2
    Views
    156

    traxxas 2.5 and 2.5r

    Hi Can anyone tell me the difference between a 2.5 and a 2.5r engine? Thanks
  7. Replies
    17
    Views
    352

    Hi Sorry its BMT (before my time) best of luck!

    Hi Sorry its BMT (before my time) best of luck!
  8. Replies
    120
    Views
    7,510

    Hi BlazerSS Checking in on the build, thanks for...

    Hi BlazerSS Checking in on the build, thanks for the updates. Gotta be the best build I have ever seen. Looks better with the stainless cup. Still green with purple envy. Definately better than...
  9. Replies
    5
    Views
    125

    Hi I found that while you have your ez starter...

    Hi I found that while you have your ez starter off, looking from the front to the back at the bottom of the starter, where the one way bearing fits, If you drill a hole dead center the size of a wd...
  10. Replies
    17
    Views
    352

    Hi Sounds like you are runnning a non-traxxas...

    Hi Sounds like you are runnning a non-traxxas carb, cause a 2.5 and a 3.3 traxxas carb are the same and do not use a sleeve. Also they are plastic carbs. Is your carb metal or plastic? Check it...
  11. Replies
    4
    Views
    308

    Thanks for the suggestions, but I am about $30...

    Thanks for the suggestions, but I am about $30 into rechargeable AA's, hence the reason for looking for a 5 AA battery holder that fits in a traxxas battery box. I saw one, but forgot the site, can...
  12. Replies
    4
    Views
    308

    5AA battery holder

    Hi I saw a 5AA cell battery holder that fit the traxxas battery box a few months ago but failed to copy down the info. Can anybody hook me up? Thanks
  13. Replies
    2
    Views
    110

    Hi You can check and see if the one screw is...

    Hi You can check and see if the one screw is protruding on the transmission on the front end of the side that the exhaust pipe is on. Try poking a small nail down into the hole. What I did was...
  14. Replies
    120
    Views
    7,510

    Wow Blazer! You are doing what most guys dream...

    Wow Blazer! You are doing what most guys dream about doing, it's fantastic. I'm green with purple envy. Wish you the best build ever, and keep the pics coming. Again, great job
  15. Thread: Run away

    by robert f.
    Replies
    8
    Views
    242

    Hi Sorry bout your truck. If you will search...

    Hi Sorry bout your truck. If you will search this site you will find the answers you need. Usually a signal interrupt causes your problem, could be an outside source (interference) or could be...
  16. Replies
    13
    Views
    408

    Hi There is a correct way to put a clutch spring...

    Hi There is a correct way to put a clutch spring on, or a better way. If you search for the link on this site I am sure you will find an answer to your question.
  17. Thread: NITRO Newbie

    by robert f.
    Replies
    22
    Views
    238

    Hi Nitro Newbie Welcome to fuel. The answer to...

    Hi Nitro Newbie Welcome to fuel. The answer to your glow igniter question is no, you do not need one with an ez starter. The starter wand replaces it. Plenty of help out there just ask.
  18. Hi again. Forgot to tell you go on e bay and get...

    Hi again. Forgot to tell you go on e bay and get an owners manual for it That is your bible for right now, tells you everything you need to know including break-in and maintenance and parts...
  19. Hi Welcome to the world of rc. Sounds like the...

    Hi Welcome to the world of rc. Sounds like the ez wand needs to be charged. Until then see if u can spin the motor over by hand. On the exhaust side of the motor looking at the car from the side...
  20. Replies
    4
    Views
    159

    Thanks for the info, appreciate it.

    Thanks for the info, appreciate it.
  21. Replies
    4
    Views
    159

    carburated t maxx

    Hi I have a t maxx with a metal carburetor and a brass adapter sleeve. What expoxy or glue would I use to glue the sleeve to the carb? Thanks
  22. Hi Try this, Get a small length of fuel line,...

    Hi Try this, Get a small length of fuel line, disconnect your fuel line from the carburetor, attach the new fuel line to the inlet on the carburetor. Then get a spray bottle of soapy water and...
  23. Replies
    68
    Views
    986

    Hi Read your problem. Did you put the ring that...

    Hi Read your problem. Did you put the ring that goes between the glow plug and the engine on right? The ring needs to go flat side down to get a good seal, or you could have the problems you are...
  24. Replies
    68
    Views
    986

    Hi Read youl link Stupid question Have you put...

    Hi Read youl link Stupid question Have you put the ring that goes between the glow plug and the engine on the right way? It needs to gol flat side down. Also try turning the engine over with the...
  25. Replies
    16
    Views
    644

    Hi Need to make a correction! For the better...

    Hi Need to make a correction! For the better tranny mount screws, use traxxas #2584 3x12 cooling head capscrews. Tried them and they work great.
Results 1 to 25 of 47
Page 1 of 2 1 2