Search:

Type: Posts; User: c0rpse

Page 1 of 4 1 2 3 4

Search: Search took 0.30 seconds.

  1. Replies
    5
    Views
    430

    Yep, I would pass on it. I bought a brushed revo...

    Yep, I would pass on it. I bought a brushed revo this summer rtr for $180 with a spectrum radio system and a bad titan motor. Even with mmm, I wouldn't pay more than $300 used. That deal from...
  2. Replies
    11
    Views
    349

    How often do you check and tighten slipper? ...

    How often do you check and tighten slipper? Also, I have to darn near lock the slipper on 3s. How tight do you have the slipper?
  3. Replies
    20
    Views
    662

    Most tracks won't let you run 1/8 parts in a 1/10...

    Most tracks won't let you run 1/8 parts in a 1/10 class.
  4. Replies
    20
    Views
    662

    Agreed. The castle motor is a great price linked...

    Agreed. The castle motor is a great price linked above. The other 2 are sensored which I prefer. Dont think you could go wrong with any of those.
  5. Looks and sounds to me like the slipper is...

    Looks and sounds to me like the slipper is loose/pads are worn or the pinion isn't tight and slipping on the motor shaft.
  6. Replies
    2
    Views
    410

    Start Here...

    Start Here
  7. Replies
    5
    Views
    246

    Usually just remove the esc even if it says it's...

    Usually just remove the esc even if it says it's water proof just to be on the safe side. All my servos that I bash with are water proof, and they are too big of a pain to remove every time anyway. ...
  8. Replies
    5
    Views
    246

    I remove electronics when I wash down mine. Then...

    I remove electronics when I wash down mine. Then I blow it out really well with an air compressor. tweezers or really small needle nose pliers might help get the pebble in the fan if you can't...
  9. Replies
    33
    Views
    863

    No battery connectors come with it as far as I...

    No battery connectors come with it as far as I know. Only time I ever got battery connectors was with the mmm through traxxas powerup program. The mounting bracket can be had at any lhs for around...
  10. Replies
    3
    Views
    399

    Paint job is slick. You air brush it?

    Paint job is slick. You air brush it?
  11. Replies
    9
    Views
    580

    http://s777.photobucket.com/albums/yy57/c0rpsejock...

    http://s777.photobucket.com/albums/yy57/c0rpsejockey/?action=view&current=20131026_180305_zps2fbad579.jpg

    Jc finisher with a trophy buggy wing and mount. I cut my own aluminum mounting plate for...
  12. Replies
    9
    Views
    580

    Rc8.2e bodies fit pretty well with a bit of...

    Rc8.2e bodies fit pretty well with a bit of creative trimming. I have seen many use kyosho 777 bodies. I used a jc finisher body for rc8.2e, but I really like the look of the pl bulldog. I have...
  13. Replies
    76
    Views
    2,133

    Yep, the "no load" part of that statement is key....

    Yep, the "no load" part of that statement is key. Since lower kv motors have more torque, they are affect less by the weight of the truck and drag on the drive tran. Thats why they run cooler and...
  14. Replies
    3
    Views
    523

    I think it will be a sweet setup.

    I think it will be a sweet setup.
  15. Replies
    76
    Views
    2,133

    Basically means rpm per volt. So for a 2400kv...

    Basically means rpm per volt. So for a 2400kv motor, each additional volt gives you 2400 more rpms. All motors have a max rpm, and that helps you determine how much voltage you can run on a given...
  16. Hobbywing sc8-wp. Water proof, 120a and 4s max. ...

    Hobbywing sc8-wp. Water proof, 120a and 4s max. I have one that I swap around from emaxx and 4wd slash for rain and snow.
  17. Thread: newb needs help

    by c0rpse
    Replies
    7
    Views
    319

    3903 internals are the same as the brushless...

    3903 internals are the same as the brushless edition. Motor plate and cover are different, but do not need to be replaced to upgrade to brushless. You may want to swap to 17mm adapters and wheels. ...
  18. Replies
    18
    Views
    511

    I still use stock setup for snow bashing. I used...

    I still use stock setup for snow bashing. I used the et-3s and castle 1415 2400kv on 3s for bashing for a while until I picked up an mmp and went to 4s. The et-3s came out of a traxxas funny car. ...
  19. Replies
    10
    Views
    841

    What everyone has been trying to explain is that...

    What everyone has been trying to explain is that although traxxas lists the revo as 1/10 scale, you really need 1/8 scale electronics. The vehicle weight and rotating mass of the drive tran is too...
  20. Replies
    3
    Views
    292

    What servo and what is votage output of the bec? ...

    What servo and what is votage output of the bec? Can you verify with a multi meter?
  21. Thread: ESC Help

    by c0rpse
    Replies
    10
    Views
    805

    Ah, totally forgot about that. It does single...

    Ah, totally forgot about that. It does single beep while powered on. He will be stuck at 1.33 though btw. He is using an et-3s.
  22. Thread: ESC Help

    by c0rpse
    Replies
    10
    Views
    805

    Eew...When you say working, throttle and reverse...

    Eew...When you say working, throttle and reverse work ok? 0 trims and I would try to calibrate again. If that doesnt work, you may have a problem with the esc. Its just weird that your motor is...
  23. Thread: ESC Help

    by c0rpse
    Replies
    10
    Views
    805

    Are you able to disable link live and test?

    Are you able to disable link live and test?
  24. Thread: ESC Help

    by c0rpse
    Replies
    10
    Views
    805

    That's fine. If you are using a non tqi rx/tx,...

    That's fine. If you are using a non tqi rx/tx, you probably just need to turn off link live feature using the castlink. It is located in the advanced tab. I can reproduce your exact problem by...
  25. Thread: ESC Help

    by c0rpse
    Replies
    10
    Views
    805

    Usually a problem with the rx (receiver). ...

    Usually a problem with the rx (receiver).

    Check your receiver connection from the esc.
    Make sure it is seated properly.
    If you are using a non traxxas rx, make sure the esc is not plugged...
Results 1 to 25 of 78
Page 1 of 4 1 2 3 4